Panasonic Toughbook CF-29N3LG6BM, Operating Instructions Manual

27

T

roub

leshooting

The power indicator is not
lit

The computer does not op-
erate when a USB device is
connected
[Enter Password] is dis-
played
POST Startup Error(s) is
displayed
Windows startup, or an op-
eration is extremely slow

The date and time are incor-
rect

When resuming from the
standby or hibernation
mode, [Enter Password]
does not appear even if a
password has been set in the
Setup Utility

When the administrator
password is forgotten

When “Remove disks or
other media. Press any key
to restart” (or a similar mes-
sage) is displayed

[ E x e c u t i n g   B a t t e r y
Recalibration] screen is dis-
played

When a problem occurs, refer to this page.  The “Reference Manual” also contains detailed information.  If a problem appears to be
related to a software application, read the software related manual.  If you still cannot troubleshoot the problem, contact Panasonic
Technical Support. (

 page 44) You can use the PC Information Viewer to check the computer’s usage status. (

“Dealing with Problems (Advanced)”)

Dealing with Problems 

(Summary)

 Starting Up

Check the cable connection for the AC adaptor.
Check to see if a charged battery pack is properly installed.
Remove the battery pack and disconnect the AC adaptor, then connect them again.
The computer may not operate when certain USB devices are connected.  Disconnect the
USB device, or set [Legacy USB Support] to [Disable] in [Advanced] menu of the Setup
Utility.
Input your Supervisor Password or User Password. If you have forgotten it, contact Pana-
sonic Technical Support.

 page 26

Press   

F9

   in the Setup Utility (

 “Setup Utility”).   This will restore the Setup

Utility’s settings to their default values (except the password settings).  Then, the Setup
Utility must be run once again for you to input the appropriate operating environment
settings.  (The processing speed depends on the application software used, so this opera-
tion may not cause the processing speed to increase.)
If you install resident software after purchasing this computer, disable the resident software.
When Indexing Service is enabled, Windows operation becomes slower.
Disable Indexing Service in the following menu.
[start] - [Search] - [Change preferences] - [Without Indexing Service]
You can set the date and time using the following menu.
[start] - [Control Panel] - [Date, Time, Language, and Regional Options] - [Date and Time]

  When the computer is connected to a LAN, confirm the date and time of the server.

If you continue to experience problems, the internal battery maintaining the clock may
need to be replaced.  Contact Panasonic Technical Support.

  This computer will not correctly recognize the date and time starting from the year 2100

A.D.
Even when a password has been set in [Security] menu of the Setup Utility, [Enter Pass-
word] does not appear when the computer resumes from the standby or hibernation mode.
If you want to use the security function when using the standby or hibernation mode, use
the Windows password as follows:

1

Select [start] - [Control Panel] - [User Accounts], and select the account for which the
password will be set.

2

Select [Create a password], input the password, and then [Create Password].

3

Add the check mark for [Prompt for password when computer resumes from standby]
in [Control Panel] - [Performance and Maintenance] - [Power Options] - [Advanced].

If you have created a password reset disk (

 page 15), a message is displayed when you

fail to correctly enter the password. Follow the message’s instructions and set the pass-
word again by using the password reset disk.
If you have not created a password reset disk, after reinstalling, setup Windows and then
set the password again.
This means a floppy disk that does not contain system startup information has been left in
the floppy disk drive. Remove the floppy disk, and press any key.
This message may appear when certain USB devices are connected. Remove the USB de-
vice, or set [Legacy USB Support] in [Advanced] menu of the Setup Utility to [Disable].
If the message still appears even after trying the above two measures, this may be an indica-
tion that some type of hard disk failure has occurred. Contact Panasonic Technical Support.
When Windows is shut down during the Battery Recalibration procedure, if you select
[Cancel] in the [End Program] screen, Windows shutdown is aborted. In this case,  Battery
Recalibration will begin the next time the computer is started. To start up Windows, turn
off the computer by sliding the power switch, and then turn it back on again.