Panasonic TX-55DS352E, Operating Instructions Manual

English

   - 11 -

Switching On/Off

To Switch the TV On

Connect the power cord to a power source such as a 

wall socket (220-240V AC, 50 Hz). 
To switch on the TV from standby mode either:

• 

Press the 

Standby

 button, 

Pro/-

 or a 

numeric button on the remote control.

• 

Press the centre of the joystick on the TV in or push 

it up/down until the TV comes on from standby.

To Switch the TV Off

Press the 

Standby 

button on the remote control or 

press the centre of the joystick on the TV in and hold 

it down for a few seconds, the TV will switch into 

standby mode.

To power down the TV completely, unplug the 

power cord from the mains socket.

Note:

  When  the  TV  is  switched  into  standby  mode,  the 

standby  LED  can  blink  to  indicate  that  features  such  as 

Standby Search, Over Air Download or Timer is active. The 

LED can also blink when you switch on the TV from standby 

mode.

First Time Installation

When turned on for the first time, the language 

selection screen is displayed. Select the desired 

language and press 

OK

.

On the next screen, set your preferences using the 

directional buttons.

Note:

 Depending on the 

Country

 selection you may be asked 

to set and confirm a PIN at this point. The selected PIN cannot 

be 0000. You have to enter it if you are asked to enter a PIN 

for any menu operation later.

About Selecting Broadcast Type

Digital Aerial:

 If 

Digital Aerial

 broadcast search 

option is turned on, the TV will search for digital 

terrestrial broadcasts after other initial settings are 

completed.

Digital Cable:

 If 

Digital

Cable

 broadcast search 

option is turned on, the TV will search for digital cable 

broadcasts after other initial settings are completed. 

According to your other preferences a confirmation 

message may be displayed before starting to search. 

Select 

YES

 and press 

OK

 to proceed. To cancel 

operation, select 

NO

 and press 

OK

. You can select 

Network

 or set values such as 

Frequency

, 

Network 

ID

 and 

Search Step

. When finished, press 

OK

 button. 

Note:

 Searching duration will change depending on the 

selected 

Search Step

.

Analogue: 

If 

Analogue

 broadcast search option is 

turned on, the TV will search for analogue broadcasts 

after other initial settings are completed.
Additionally you can set a broadcast type as your 

favourite one. Priority will be given to the selected 

broadcast type during the search process and the 

channels of it will be listed on the top of the Channel 

List. When finished, press 

OK

 to continue.

You can activate 

Store Mode

 option at this point. 

This option will configure your TV’s settings for store 

environment and depending on the TV model being 

used, the supported features of it may be displayed 

on the top of the screen as an info banner. This option 

is intended only for store use. It is recommended to 

select 

Home Mode

 for home use. This option will be 

available in 

Setup>More

 menu and can be turned 

off/on later. 
Press 

OK

 button on the remote control to continue 

and the 

Network/Internet Settings

 menu will be 

displayed,  if  you  confirm  the  previously  displayed 

message asking whether you want to do the network 

settings. Please refer to 

Connectivity

 section to 

configure a wired or a wireless connection. After the 

settings are completed press 

OK

 button to continue. 

To skip to the next step without doing anything select 

No

 and press the 

OK

 button when the message is 

displayed asking whether you want to do the network 

settings.
After the initial settings are completed TV will start 

to search for available broadcasts of the selected 

broadcast types.
After all the available stations are stored, scan results 

will be displayed. Press 

OK

 to continue. The 

Edit 

Channel List

 menu will be displayed next. You can 

edit the channel list according to your preferences or 

press the 

Menu

 button to quit and watch TV.

While the search continues a message may appear, 

asking whether you want to sort channels according 

to the LCN

(*)

. Select 

Yes

 and press 

OK 

to confirm

.

(*) 

LCN is the Logical Channel Number system that organizes 

available  broadcasts  in  accordance  with  a  recognizable 

channel number sequence (if available).

Note:

 Do  not  turn  off  the  TV  while  initializing  first  time 

installation. Note that, some options may not be available 

depending on the country selection.