background image

5

CAUTION

Do not place any heavy object on top or get on top of the product.

Failure to observe this may cause tip-over or drop of the product resulting in injury. It may also cause 
damage or deformation of the product.

Be careful not to catch your hand caught when closing the opening/closing parts.

Failure to observe this may cause injury. Failure to observe this may cause electrical shock.

Turn off the power of this unit at servicing.

Failure to observe this may cause fire or electrical shock.
Exercise extra care when touching inside the unit such as roller cleaning.

Do not place this unit where temperatures vary frequently (e.g. near an air conditioner or 
near a heater).

Failure to observe this may cause fire or electrical shock resulting from condensation generated in 
this unit.

Do not lift or tilt this unit.

Failure to observe this may cause injury resulting from falling down.

Do not place this unit on a shaky base, or a tilted, a frequently shaking, or a frequently 
impact receiving place.

Failure to observe this may cause injury resulting from dropping or falling down.

Do not place this unit in direct sunshine or near a heater.

Failure to observe this may cause fire or electrical shock resulting from increase in internal 
temperature or melting of the cover or cable sheath.

Do not block the ventilation openings of this unit.

Failure to observe this may cause fire because this unit is internally filled with heat.

Do not insert any foreign objects into this product.

Failure to observe this may cause fire or electric shock.

Stop operation if something is wrong with this product.

Stop operation, if smoke or smell comes from this product, or abnormal sound is heard, or 
deterioration

Do not connect/disconnect the signal cable with wet hands.

Failure to observe this may cause electric shock.

Take measures to prevent the interior of the product from exposure to water.

Failure to observe this may cause electric shock

Do not damage the power cable and the plug.

Failure to observe this may cause electric shock

Summary of Contents for UD-7900N14EU























Reviews: