Panasonic VB-44210G User Manual Download | Manualshive

Page: 240 / 394

background image

Chapter 5. DSLT Features

Section 700 - Operation

5-22

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

• An extension can only have one call camped on at a time. For example, if

Extension 152 camps on to Extension 153, another extension cannot camp
on to 153, as long as 152 is camped on.

• An extension that has initiated a camp-on cannot receive a camp-on. For

instance, if Extension 200 has camped on to Extension 300, another
extension cannot camp on to 200.

• For CPC-B 5.03 and above, callbacks are not forwarded. For example, if

Extension 200 is call forwarded to Extension 300, Extension 200 can
register a callback request to Extension 400. When the callback request is
returned, it will ring Extension 200 and will not follow call forwarding.

Conference Calls

(All Versions)

Description

Conference Calls allow an extension user to add a party to an existing
conversation.

DSLT users can create the following types of Conference Calls:

• One outside line and two extensions (three-party Conference Call)

• Two outside lines and one extension (three-party Conference Call)

• Three extensions (Intercom Conference Call)

Operation

To add an extension:

1. Press

the

HOLD

key to place the current call on hold.

2. Dial the number of the extension you wish to add to the call.

3. Press

CONF

when your call is answered.

To add an outside number:

1. Press

the

HOLD

key to place the current call on hold.

2. Call the outside number.

«
...
238
239
240
241
242
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Panasonic Pages: 252

Brand: Panasonic Pages: 8

EASA-PHONE KX-T123220

Brand: Panasonic Pages: 6

DBS 576 Section 300

Brand: Panasonic Pages: 362

DBS 576 Section 300

Brand: Panasonic Pages: 91

Brand: Uniden Pages: 49

Brand: Jabra Pages: 16

SP200 - QUICKSTART GUIDE 1

Brand: Jabra Pages: 372

JABRA FREEWAY HFS100

Brand: Jabra Pages: 40

Brand: Jabra Pages: 3

Brand: Panasonic Pages: 45

Brand: M-Life Pages: 16

IntelliGate A150

Brand: Aastra Pages: 85

Brand: Marmitek Pages: 27

Brand: Vortex Pages: 19

Brand: Talkswitch Pages: 65

Brand: LEGRAND Pages: 3

Brand: Uniden Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands