Panasonic VB-44210G User Manual Download | Manualshive

Page: 341 / 394

background image

Section 700-Operation

Appendix B. CPC-AII/B 8.0 Feature Update

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page B-15

MSG (Message) Key

44-Series phones only
CPC-AII/B Version 8.0, CPC-S/M Version 2.0, or CPC-EX Version 1.0 only

Description

The MSG key on the VB-44225 Large-Display Phone adds the following
functionality to the phone:

•

Auto-Callback.

If a callback message has been left by another

extension, you can press the MSG key to place an automatic callback to
the extension that sent the message. If more than one callback message
has been received, pressing the MSG key will perform auto-callback in
the order received.

•

Auto-Answer Voice Message.

You can press the MSG key to

automatically access your voice mailbox. The phone will dial your
voice mailbox and send access codes (if programmed) for retrieving
new messages.

Programming

See

Section 400 - Programming (Appendix D)

for more detailed

programming information.

Operation

To Program Voice Mailbox Access Codes into the MSG Key:

Press PROG MSG [16-digit number] HOLD

The display will reflect “Regist Data”.

To Confirm a Voice Mailbox Access Code Programmed into the
Message Key..

Press CONF MSG.

The programmed access code will be displayed.

Notes

Operation With Message Waiting Indicator.

The Message Waiting

Indicator on the phone’s upper right corner will flash whenever a callback
message or voice message has been received.

Operation During Call States.

The MSG key will work only when the

phone is idle, receiving dial tone, or in Directory Mode (via select key).

Operation If Phone Has Both a Callback Message from another
Extension and a Voice Message.

Messages are accessed in a First In, First

Out order. If the callback message was received before the voice message,
then pressing the MSG key will activate Auto-Callback first. Likewise, if

«
...
339
340
341
342
343
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Unimec Pages: 48

Bell & Gossett ecocirc XL Series

Brand: Xylem Pages: 62

Brand: TANDBERG Pages: 12

Brand: NEC Pages: 266

Brand: AT&T Pages: 7

Brand: Medion Pages: 220

Brand: Uniden Pages: 52

DECT1725 Series

Brand: Uniden Pages: 44

Brand: Northland Pages: 7

Brand: Ericsson Pages: 2

Brand: Commax Pages: 16

Brand: TMC Pages: 91

Brand: AT&T Pages: 45

Brand: Panacom Pages: 16

Brand: VTech Pages: 38

Brand: Inter-Tel Pages: 48

Brand: Nebulink Pages: 12

Brand: Hamilton Beach Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands