background image

5

 

Do not place the Plasma TV or its stand on a 
sloped or unstable surface.

  The Plasma TV may fall or tip over.

 

Do not support the Plasma TV on a non-
specified pedestal.

 

Do not place the Plasma TV on furniture that can 
easily be used as steps, such as a chest of drawers.

 

Do not climb or allow children to climb on the Plasma TV

 

Place or install the Plasma TV where it cannot 
be pushed, pulled over or knocked down.

 

Route all cords and cables such that they cannot 
be tripped over or pulled by curious children.

 

Do not place any objects on top of the Plasma TV.

  If water spills onto the Plasma TV or foreign 

objects get inside it, a short-circuit may occur, 
which could result in fire or electric shock. If any 
foreign objects get inside the Plasma TV, please 
consult an Authorized Service Center.

 

 

In the unlikely event that you receive a shock 
from this product, it is possible that your 
household outlet may be wired improperly. 

  Have an electrician verify that the TV’s outlet is 

properly wired. If the symptom persists, have the 
TV serviced by a qualified authorized technician.

 

To prevent the spread of fire, keep 
candles or other open flames away 
from this product at all times

 

AC Power Supply Cord

To prevent fire or electric shock:

 

The Plasma TV is designed to operate on a 120 
V AC, 60 Hz service. Insert the power cord plug 
as far as it will go into the wall socket.

  If the plug is not fully inserted, heat may generate, 

which could cause a fire.

 

The included power cord is for use with this unit only.

 

Do not use any power cord other than that 
provided with this TV.

 

Do not handle the power cord plug with wet hands.

 

Do not do anything that might damage the 
power supply cord.

 

When disconnecting the power supply cord, 
hold the plug, not the cord.

 

Do not use the power supply cord if the plug or 
cord is damaged.

  Replace the cord or contact your Authorized Service Center.

 

Do not use a 3-prong to 2-prong AC plug adapters 
to connect your TV’s plug to the wall outlet.

  Doing so will defeat the TV plug’s safety feature, 

which can lead to a shock hazard. If the wall outlet 
does not accommodate a 3-prong plug, have a 
qualified electrician replace your outlet and check 
the associated wiring.

 

If water or an object gets inside the Plasma TV, if the 
Plasma TV is dropped, or if the enclosure becomes 
damaged, unplug the power supply cord immediately.

  A short-circuit may occur, which could cause a fire. 

Contact an Authorized Service Center for an evaluation.

 

Radio waves

 

Do not place this TV in any medical institutions 
or locations with medical devices.

  Radio waves from this TV may interfere with the medical 

devices and cause accidents due to the malfunction.

 

Do not use this TV near any automatic control 

devices such as automatic doors or fire alarms.

  Radio waves from this TV may interfere with the 

automatic control devices and cause accidents 
due to the malfunction.

 

Keep this TV away at least 9 inches (22 cm) from the 
location where a cardiac pacemaker is implanted.

  Radio waves from this TV may interfere with the 

operation of the pacemaker.

 

Handling the power supply cord

 

Insert the power plug fully into the socket outlet. 
(If the power plug is loose, it could generate heat 
and cause fire.)

 

Ensure that the power plug is easily 
accessible.

 

Ensure the earth pin on the power plug is 
securely connected to prevent electrical shock.

•  An apparatus with CLASS I construction shall 

be connected to a power socket outlet with a 
protective earthing connection.

 

Do not touch the power plug with a wet hand. 
(This may cause electrical shock.)

 

Do not use any power cord other than that 
provided with this TV. (This may cause fire or 
electrical shock.)

 

Do not damage the power cord. (A damaged 
cord may cause fire or electrical shock.)

•  Do not move the TV with the cord plugged in the 

socket outlet.

•  Do not place a heavy object on the cord or place 

the cord near a high-temperature object.

•  Do not twist the cord, bend it excessively, or 

stretch it.

•  Do not pull on the cord. Hold onto the power 

plug body when disconnecting cord.

•  Do not use a damaged power plug or socket 

outlet.

 

If a problem occurs (such as no picture or 
no sound), or if smoke or an abnormal odor 
is detected from the Plasma TV, unplug the 
power supply cord immediately.

  Continued use of the TV under these conditions 

might cause a fire or permanent damage to the TV. 
Have the TV evaluated by an Authorized Service 
Center. Servicing of the TV by unauthorized 
personnel is strongly discouraged due to its high 
voltage.

Summary of Contents for Viera TC-P50ST60

































Reviews: