P-39
PROGRAMMING (MODE 2)
(01-04)14#-(0, 1-7)#
c
INCOMING RING SIGNAL DETECTION
TIME
Detects an incoming ring signal when the signal is
longer than the time programmed for an incoming ring
signal. For example, if the time programmed of an
incoming call signal is 200 mseconds or longer, signal
that are longer than 200 mseconds are identified as a
phone call. Any signal shorter than 200 mseconds are
not considered phone signal and are disregarded.
0#: More than 50 mseconds
1#: More than 100 mseconds
2#: More than 150 mseconds
3#: More than 200 mseconds
4#: More than 250 mseconds
5#: More than 300 mseconds
6#: More than 350 mseconds
7#: More than 400 mseconds
(01-04)15#-(0, 1-7)#
INCOMING RING PATTERN DETEC-
TION TIMER
Because incoming call ring patterns sometimes vary, the
timer can be set up to a maximum of 14 seconds to
ensure that the ring cycle on incoming call is not cut off
prematurely.
For example, if the ring cycle of a call is 4 seconds (1
second of the signal and 3 seconds for the pause), the
timer must be set for 4 seconds.
This is to prevent the call from getting cut off before the
full ring cycle. If you set the time for 3 seconds for a
call ring pattern that has a 4-second cycle, you may
cause the call to be cut off prematurely.
0#: 3 seconds
1#: 4 seconds
2#: 5 seconds
3#: 6 seconds
(01-04)16#-(0 or 1)#
FL/R KEY TYPE
Sets the function of FL/R key.
To set to use FL/R key as FLASH or TIMED BREAK
RECALL:
0#: FLASH
1#: TIMED BREAK RECALL
(01-04: Exchange
line No.)
(01-04: Exchange
line No.)
4#: 8 seconds
5#: 10 seconds
6#: 12 seconds
7#: 14 seconds
(01-04: Exchange
line No.)
(01-04: Exchange
line No.)
(01-04: Exchange
line No.)
(01-04: Exchange
line No.)
(01-04)17#-(0 or 1)#
DT DETECTION AT OUTGOING CALL
When making an outgoing call, it is possible to dial
without pause by detecting the dial tone from Exchange
line or PBX.
To set each line to detect the dial tone or not.
0#: Does not detect Dial Tone
1#: Detects Dial Tone
(01-04)18#-(0 or 1)#
BUSY TONE DETECTION
When making an outgoing call, using auto repeat dial it
is possible to detect the Busy Tone if the line of the
other party is busy.
To set each line to detect the Busy Tone or not.
0#: Does not detect Busy Tone
1#: Detects Busy Tone
NOTE : When making an on-hook dial from a Propri-
etary Telephone, Auto Repeat Dial operation
will be initiated by Busy Tone detection (Auto
Repeat Dial setting is required).
(01-04)19#-(1-3)#
M
END DETECTION OF OUTGOING CALL
In case of outgoing call, it is possible to automatically
release the Exchange line when the other party ends the
call.
To set how to detect the other party’s end.
None (No Detects)
1#: Detects by the polarity reverse signal
2#: Detects by Break signal
NOTE : • Two or more settings can be assigned.
• To delete the input data, press the same data
number again.
Summary of Contents for VoiceSonic VB-9411AD
Page 60: ...MEMORANDUM ...
Page 94: ...CONNECTION OF OPTIONAL UNITS I 34 MEMORANDUM ...
