background image

Canada  only:  Not  to  be  installed  in  a  ceiling  thermally  insulated  to  a  value  greater  than  R40.

Do  not  disassemble  the  unit  for  reconstruction.  It  may  cause  fire  or  electric  shock.

Ceiling  joist  must  be  subjected  to  static  load  more  than  five  times  the  weight  of  the  product.

This  product  must  be  properly  grounded.

Do  not  install  this  ventilating  fan  where  interior  room  temperature  may 
exceed  104°F(40°C).

Make  sure  that  the  electric  service  supply  voltage  is  AC  120V,  60Hz.

Follow  all  local  electrical  and  safety  codes,  as  well  as  the  National 
Electrical  Code  (NEC)  and  the  Occupation  Safety  and  Health  Act  (OSHA).

Always  disconnect  the  power  source  before  working  on  or  near  the  fan, 
motor,  light  fixture  or  junction  box. 

Protect  the  supply  wiring  from  sharp  edges,  oil,  grease,  hot  surfaces,
chemicals  or  other  objects.

Do  not  kink  the  supply  wiring.

Provide  make  up  air  for  proper  ventilation.

For  general  ventilating  use  only.  Do  not  use  to  exhaust  hazardous  or 
explosive  materials  and  vapors.

Not  for  use  in  cooking  area.  (Fig.B)

The  special-purpose  or  dedicated  parts,  such  as  mounting
fixtures,  must  be  used  if  such  parts  are  provided.

3

Do  not  install  the  unit  where  ducts  are  configured  as  shown 
in  Fig.A.

Do  not  install  with  a  method  which  is  not  approved  in  the  instrucions.

Adaptor

USA  only:  This  product  has  two  fluorescent  lamps  that  contain  mercury.  Disposal  may  be
regulated  in  your  community  due  to  environmental  considerations.  For  disposal  or  recycling 
information,  please  contact  your  local  authorities  or  visit  Panasonic  website: 
http://www.panasonic.com/environmental  or  call  1-888-769-0149.

CAUTION

WARNING

Summary of Contents for WhisperLite FV-08VQL6













Reviews: