Network
62
Network settings
Item
Settings
Description
NW link down detection
Off
♦
/ On
Specifies whether to detect disconnected network connection of
Camera port/Client PC.
Bandwidth control
Unlimited
♦
/ 32Kbps / 64Kbps /
12
8
Kbps / 256Kbps / 512Kbps /
1024Kbps / 2Mbps / 5Mbps /
10Mbps
Specifies the maximum rate for data transmitted to the network.
•
The transmission amount is not limited in the case of an
MPEG-4 live image.
Port forwarding
Specifies whether port forwarding is enabled. To configure this
setting, click the [Setup >>] button.
HTTP port number
Port number input
(
8
0
♦
)
Sets the HTTP port used when sending images in the range of
1 to 65535. Normally this setting is
8
0.
•
Depending on network settings, changing the HTTP port
number may make communication impossible. If this
happens, contact your network administrator.
•
Do not specify any of the following numbers for an FTP port
number, site alarm port number, or port forwarding port
number.
20, 21, 23, 25, 42, 53, 67, 6
8
, 69, 79, 105, 110, 123, 161,
162, 546, 547, 995, 10001, 10002, 10003, 10004, 10005,
10006, 10007
FTP port number
Port number input
(21
♦
)
Specifies the recorder FTP port number in the range of 1 to
65535. Normally this setting is 21.
•
Do not specify any of the following numbers for an HTTP
port number, site alarm port number, or port forwarding port
number.
20, 23, 25, 42, 53, 67, 6
8
, 69, 79,
8
0, 105, 110, 123, 161,
162, 546, 547, 995, 10001, 10002, 10003, 10004, 10005,
10006, 10007
Network setup - Camera port/Client PC port
DHCP
Off
♦
/ On
Specifies whether a DHCP server is used.
•
Select [On] to obtain the IP address, subnet mask, and
default gateway from a DHCP server. Select [Off] to enter
them manually.
IP address
Address input
*1
When [DHCP] is [Off], specify the IP address here.
Subnet mask
Address input
*1
When [DHCP] is [Off], specify the subnet mask here.
Default gateway
Address input
*1
When [DHCP] is [Off], specify the default gateway here.
Line speed
Auto
♦
/ 1000M-Full / 100M-Full /
100M-Half / 10M-Full / 10M-Half
Specifies the data line speed.
Network setup - Maintenance port
IP address
Address input
*1
Specifies the IP address.
Subnet mask
Address input
*1
Specifies the subnet mask.
DNS setup
DNS
Off
♦
/ Auto / Manual
Specifies whether a DNS is used.
•
Selecting [Auto] enables auto detection of the DNS server.
This setting is available only when [On] is selected for the
[DHCP] setting of the Client PC port (page 61).
•
When [Manual] is selected, a primary address and
secondary address can be specified for the DNS server IP
address.
Primary server address
Address input (0.0.0.0
♦
)
Enter the IP address of the primary DNS server.
Secondary server address
Address input (0.0.0.0
♦
)
Enter the IP address of the secondary DNS server.
Domain name
Name input (local domain
♦
)
Enter the domain name of the recorder.
•
Enter up to 255 single-byte alpha-numeric characters,
including hyphen (-) and period (.).
•
Use an alphabetic character as the first character of the
domain name.
Summary of Contents for WJND400 - NETWORK DISK RECORDER
Page 73: ...4 ...
