background image

14

Facsimile Features

 Transmitting a Document Stored in Memory

1

(To use the Platen Glass,
see page 17.)

or

2

5

NOTE

1. If the memory overflows while original(s) are being scanned for transmission to a single destination, the

machine will operate in the following manner:
 •

If the Fax Parameter No. 082 (Quick Memory XMT) is set to "Valid"

The document is transmitted up to the portion that was stored into memory, and an error message

Memory Full

” is displayed.

 •

If the Fax Parameter No. 082 (Quick Memory XMT) is set to "Invalid"

The document is transmitted up to the portion that was stored in memory, and then switches to direct
transmission, and transmits the remaining original(s) in the ADF during the same phone call.

Documents can be quickly scanned, and stored in memory
before transmission.
This feature allows you to send documents to multiple
destinations without having to scan the same documents
over again. It also allows you to retrieve your original(s)
immediately without having to wait for the fax transmission
to complete.
In addition to memory transmission, the machine supports
the direct transmission feature. In direct transmission, a
document is transmitted without storing it into memory.

Memory Transmission

Original(s)

Stores all the
original(s) into
memory first,
and then starts
its transmission

destination
machine(s)

Memory

Quick Memory Transmission

Original(s)

Starts
transmitting
when the first
page is stored
in memory

destination
machine(s)

Memory

Sending Documents

Summary of Contents for WORKIO DP-8035





































































































































































































Reviews: