Step 3
Secure the safety wire angle (accessory) to the anchor bolt (for
connecting the safety wire), and connect the safety wire (accessory).
①
Mount a nut so that the safety wire angle
is secured on the anchor bolt.
②
Remove the safety wire from the safety
wire angle.
③
Insert the groove of the portion
❶
of the
safety wire angle into the anchor bolt.
④
Close the safety wire angle while inserting
the groove of the portion
❷
of the safety
wire angle into the anchor bolt.
⑤
Connect the safety wire to the safety wire
angle again.
⑥
Engage the nut from beneath, and secure
the safety wire angle with top and bottom
nuts.
⑦
Engage another nut from beneath to
tighten and secure the nut that was
engaged from beneath in
⑥
in a double
nut fashion.
Note:
When the existing anchor bolt that
has been installed is used for
connecting the safety wire, the use
of 2 spacer nuts is helpful.
Step 4
Attach the safety wire.
①
Mount a nut so that the mounting chassis is
secured on the anchor bolt(for securing the
mounting chassis).
②
Attach the safety wire to the mounting chas-
sis as shown in the right illustration.
<Image of safety wire connection>
Spacer nuts
Spacer nuts
Safety wire angle
Existing anchor bolt
Safety wire
Upper side
Lower
side
Safety wire
③
Insert
②
Remove
④
Close
❷
❶
⑤
Connect
Safety wire angle
Anchor bolt
Safety wire
(Accessory)
Roof space
Ceiling board
Cables
Mounting
chassis
Step 5
Insert the anchor bolt into the mounting hole of the mounting
chassis.
To adjust the position of the Panasonic logo
on the decorative cover, rotate the mounting
chassis. Note that the Panasonic logo will
be located at approximately 180° opposite
side of a hook for the decorative cover.
Step 6
Secure the mounting chassis.
①
Secure the mounting chassis to the ceiling
board with the ceiling board fixing screws
(4
places).
Turning the ceiling board fixing screws clock-
wise provides ceiling board tightening
between the bottom of the mounting chassis
and ceiling board fixing bracket resulting in
mounting chassis securing.
Recommended tightening torque:
0.78 N·m {0.58 lbf·ft}
②
Use double nuts (locally procured) to secure the mounting chassis after inserting the anchor bolt
(for securing the mounting chassis).
Step 7
Mount the attachment plate.
①
Mount the attachment plate (accessory of the
camera) to this mounting chassis. Use fixing
screws for attachment plate (M4:accessory of
the camera) to secure the attachment plate
firmly as shown in the right illustration.
Recommended tightening torque:
0.78
N·m {0.58
lbf·ft}
Mounting
hole
Hooks (3 places)
Approx. 10°
Direction of brand logo
Anchor bolt
(for securing the mounting chassis)
Ceiling board
fixing bracket
(4 places)
Ceiling board
fixing screw
(4 places)
Turn
clockwise
Double nuts
(locally procured)
Ceiling board
Anchor bolt
(for connecting the safety wire)
IMPORTANT:
When securing this bracket on the ceil-
ing, make sure that the four ceiling
board fixing brackets are open as
shown in the right illustration.
Step 8
Connect the cables and mount the camera on the attachment plate.
Step 9
Fix the camera.
Remove the enclosure from the camera and fix the camera firmly by tightening the camera fixing
screw (red).
Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
Mounting chassis
Attachment plate
(accessory of the
camera)
Fixing screws for attachment plate (4 pcs.)
(M4:accessory of the camera)
Step 10
Adjust the camera.
After adjusting the angle of view, attach the enclosure to the camera as it was before.
Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
Step 11
Mount the decorative cover.
Mount the decorative cover on this mount
bracket.
• Align the “I” mark of the decorative cover
supplied with this mounting chassis with the
hook of the mounting chassis, press the
decorative cover against the ceiling, and rotate
the decorative cover clockwise when viewing it
from beneath to secure the cover.
Decorative cover
“I” Mark
Projections (3 places)
Projection
Hooks for the
decorative cover
(3 places)
Existing anchor bolt
Safety wire
Safety wire angle
Nut
(locally procured)
Fix the hook of the
safety wire to this
product.
Camera fixing screw (red).
Hook of the mounting chassis
Enclosure
Enclosure
