background image

Information on Disposal for Users of Waste Electrical & Electronic Equipment  
(private households)

 

This symbol on the products and/or accompanying documents means that used elec-
trical and electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to desig-
nated collection points, where they will be accepted on a free of charge basis. 
Alternatively, in some countries you may be able to return your products to your local 
retailer upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent 

any potential negative effects on human health and the environment which could otherwise arise from 
inappropriate waste handling.
Please contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legisla-
tion.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for 
further information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the cor-
rect method of disposal.

For U.S. and Canada:

Panasonic System Communications

Company of North America,

Unit of Panasonic Corporation  

of North America

www.panasonic.com/business/

For customer support, call 1.800.528.6747

Two Riverfront Plaza, Newark, NJ 07102-5490

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,  

Ontario, L4W 2T3 Canada 

(905)624-5010

www.panasonic.ca

© Panasonic System Networks Co., Ltd. 2014

For Europe and other countries:

Panasonic Corporation

http://panasonic.net

Panasonic System Networks Co., Ltd.  

Fukuoka, Japan

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

Summary of Contents for WV-SPN6FRL1



















Reviews: