25
●
Clean the filter. (Page 18)
→
Is there incrustation or dust accumulated on the sterilization
filter assembly?
●
→
故障排除
TROUBLESHOOTING
預過濾網
、
集塵過濾網(進風口)是否被灰塵等堵塞
？
除菌過濾網組件上是否附有水垢和灰塵
？
請消除堵塞
。
(第
18
頁)
請清除水垢和灰塵
。
(第
21
頁)
首先請確認以下內容
，
執行此操作後仍無法修復時
，
請拔下電源插頭
，並
聯繫經銷商進行檢查
、
維修
。
①
The air volume is small.
Is the pre-filter or the dust filter clogged with dust or the like?
●
Clean the filter. (Page 18)
→
●
→
②
●
→
●
Make sure that you have added one tablet of salt into the tray
and then pressed the salt input confirm button. (Page 15)
→
Is the door open indicator blinking?
●
→
③
Chlorine is smelt.
●
If you do not like the smell of chlorine, adjust the electrolysis
strength to "L". (Page 12)
→
④
The air coming out from
the air outlet smells bad.
●
Clean the tray, sterilization filter and water supply tank
(Pages 17, 19 and 21) and refill with new tap water. (Page 15)
→
⑤
請確認以下內容
除菌過濾網組件上是否附有水垢和灰塵
？
預過濾網
、
集塵過濾網(進風口)是否被灰塵等堵塞
？
請消除堵塞
。
(第
18
頁)
請清除水垢和灰塵
。
(第
21
頁)
按下 後是否等了
20
秒鐘
？
確認鹽粒提示燈是否在閃爍
？
門開啟提示燈是否在閃爍
？
水盤
、
除菌過濾網是否有髒漬
，
或未使用新的自來水
？
請進行水盤
、
除菌過濾網
、
供水水箱的維護保養
(
第
17
、
19
和
21
頁
)，
換上新的自來水
。
(第
15
頁)
請確認已關好前面板
。(
第
12
和
15
頁
)
因為次亞鹽素酸分解了污垢和臭氣
。
不喜歡氯(消毒)的氣味時請將電解強度調到
“
低
”
。
(第
12
頁)
確認已向水盤內放入
1
粒鹽粒後再按確認鹽粒按鈕
。
(第
15
頁)
即使等上
20
秒鐘仍完全不吹風時
，
請聯繫經銷商
。
可能發生的狀況
出風量少
出風口吹出的風有臭味
供水水箱水量不減少
不吹風
發出氯(消毒)的氣味
按下 後約
20
秒鐘為預備運轉時間
。
(第
12
頁)
Remove the incrustation and dust. (Page 21)
Is the pre-filter or the dust filter (air inlet) clogged with dust
or the like?
Water in the water supply
tank dose not decrease.
Are the tray and sterilization filter dirty, or are you not using new
tap water?
That is because hypochlorous acid decomposes dirt and odor.
Make sure that the front panel is closed. (Pages 12 and 15)
Is the salt input confirm indicator blinking?
If no air is blown out even after 20 seconds have elapsed,
contact the dealer.
The product enters preparatory operation in about 20 seconds
after is pressed. (Page 12)
Have 20 seconds elapsed after is pressed?
No air is blown out.
Remove the incrustation and dust. (Page 21)
Is there incrustation or dust accumulated on the sterilization
filter assembly?
Please confirm the following
Possible situation
If a problem is encountered, please investigate it by going through the following items.
If the problem still persists, please disconnect the power plug and contact the dealer for repair.
其
他
信
息
OTHER
INF
ORMATION
