Panasonic ZU-1870MA6T2 Specifications Download | Manualshive

Page: 3 / 11

background image

1

1. INTRODUCTION

This specification applies to the Panasonic magnetic card reader,
featuring small size, light weight and high performance.

2. COMPOSITION

The magnetic card reader is composed of the mechanical portion,
double circuits for reading.

1) Mechanical portion
The mechanical portion is mainly composed of the following parts.

1. Body (Color:Transparence)
2. Card entrance slot (Color: Black)

3. Magnetic head

4. Rubber seal

2) Circuit portion
1. Read amplifier circuit for 2 tracks

3. SPECIFICATION
3.1 CARD STANDARD
Refer to Magnetic Card Specification (9).

3.2 FUNCTION
(1) Read/Write : Read only
(2) Read timing : Ejection
(3) Compatibility : Cards and installation
(4) Installation of the transport : Horizontal direction

«
1
2
3
4
5
...
»

Summary of Contents for ZU-1870MA6T2












Reviews:

No comments

Related manuals for ZU-1870MA6T2

Brand: IDTECK Pages: 8

Brand: IDTECK Pages: 14

Brand: Laser Pages: 25

Brand: Laser Pages: 32

Brand: Onyx Pages: 136

Brand: TSL Pages: 22

Brand: Sumo Pages: 8

Brand: Aiwa Pages: 22

Brand: Aiwa Pages: 9

Brand: Onkyo Pages: 40

Quickscan QD2200

Brand: Datalogic Pages: 235

Brand: Mindeo Pages: 90

Brand: Renkforce Pages: 2

Brand: Daytona Pages: 143

Brand: Honeywell Pages: 2

Brand: Honeywell Pages: 3

MS9535 VoyagerBT

Brand: Honeywell Pages: 2

Brand: IDTECH Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands