Panasonic ZU-1870MA6T2 Specifications Download | Manualshive

Page: 9 / 11

background image

7

8. CONNECTOR DIMENSION
POST(641216-7 AMP)

9. MAGNETIC CARD SPECIFICATION
9.1 CARD SPECIFICATION

          (1)  Thickness                                    :    0.76  mm  (tolerance  ±  0.08  mm)
          (2)  Transformation                            :    2  mm  max.
(3) Impermeability rate     : More than 2.0
    (Measured by light permeance desitometer)

9.2 MAGNETIC CHARACTERISTICS
          (1)  Coercive  force  (Hc)                    :    2.4  x  10

4

A/m (300 Öe ± 12%)

(2) Residual flux (¢r) : 1.25 x 10

-8

Weber/cm

(1.25 ± 0.15 maxwell/cm)

(3) Squareness ratio (¢r/¢m) : More than 0.70

«
...
7
8
9
10
11
»

Summary of Contents for ZU-1870MA6T2












Reviews:

No comments

Related manuals for ZU-1870MA6T2

AirPro DWL-A520

Brand: D-Link Pages: 8

AirPro DWL-A520

Brand: D-Link Pages: 63

Brand: Magtek Pages: 41

Brand: Magtek Pages: 34

Brand: Magtek Pages: 34

Brand: Magtek Pages: 4

Brand: Magtek Pages: 44

Brand: Magtek Pages: 23

Brand: Magtek Pages: 28

Brand: Black Box Pages: 27

Brand: Kaya Instruments Pages: 27

Brand: Prology Pages: 17

Brand: Outland Technology Pages: 34

Brand: Blaupunkt Pages: 21

Brand: Climax Technology Pages: 4

Brand: IMS Pages: 19

LAVA SSerial-PCIe

Brand: Lava Pages: 1

Brand: Pioneer Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands