INOXPAN S.L.
V1550 N ECO:
•
•
•
•
EN
– INSTALLATION
20
V2450 N ECO:
•
Should be installed with a Ø200mm conduit, a different diameter will affect the performance
of the motor, reducing its suction capacity, increasing noise produced as well as causing
other problems.
•
The recommended length of the conduit between the hood and the motor is 4 - 6 m
maximum, a greater distance will reduce the motor's suction capacity, while a shorter
distance will increase the noise of the hood, if the latter case in inevitable, we recommend
the use of soundproofing elements.
•
It is recommended that the conduit from the hood to the motor is without sharp angles, as
they will reduce the suction capacity of the motor. If they are inevitable, try to ensure they
are not too close to the inlet or outlet of the motor (at least 0.5m away). Do not use elbow
joints of less than 90º, or place one after another, the minimum recommended distance
between them is 1m, and try to make them as open as possible.
•
The maximum total length of the conduit from the hood to the exterior should be 12 linear
metres, not counting elbow joints (one elbow joint is equivalent to 2.5 linear metres), any
longer and the suction capacity of the motor will be reduced.
V2600 ECO:
•
Should be installed with a Ø200mm conduit, a different diameter will affect the performance
of the motor, reducing its suction capacity, increasing noise produced as well as causing
other problems.
•
The recommended length of the conduit between the hood and the motor is 6 - 8 m
maximum, a greater distance will reduce the motor's suction capacity, while a shorter
distance will increase the noise of the hood, if the latter case in inevitable, we recommend
the use of soundproofing elements.
•
It is recommended that the conduit from the hood to the motor is without sharp angles, as
they will reduce the suction capacity of the motor. If they are inevitable, try to ensure they
are not too close to the inlet or outlet of the motor (at least 0.5m away). Do not use elbow
joints of less than 90º, or place one after another, the minimum recommended distance
between them is 1m, and try to make them as open as possible.
•
The maximum total length of the conduit from the hood to the exterior should be 12 linear
metres, not counting elbow joints (one elbow joint is equivalent to 2.5 linear metres), any
longer and the suction capacity of the motor will be reduced.
longer and the suction capacity of the motor will be
reduced.
metres, not counting elbow joints (one elbow joint is equivalent to 2.5 linear metres),
any
The maximum total length of the conduit from the hood to the exterior should be 12
linear
between them is 1m,
and try to make them as open as
possible.
joints
of
less
than
90º,
or
place
one
after
another,
the
minimum
recommended
distance
are not too close to the inlet or outlet of the motor (at least 0.5m away). Do not use elbow
they will reduce the suction capacity of the motor. If they are inevitable, try to ensure they
It is recommended that the conduit from the hood to the motor is without sharp angles, as
the use of soundproofing
elements.
distance will increase the noise of the hood, if the latter case in inevitable, we recommend
maximum,
a
greater
distance
will
reduce
the
motor's
suction
capacity,
while
a
shorter
The
recommended
length
of
the
conduit
between
the
hood
and
the
motor
is
4
-
6
m
other
problems.
of the motor, reducing its suction capacity, increasing noise produced as well as causing
Should be installed with a Ø150mm conduit, a different diameter will affect the performance
Summary of Contents for V.3000 N ECO
