25
24
USER MANUAL
PANDORA DXL 0110L CAR SERVICE-SECURITY SYSTEM
be pressed once again, the series of red and green flashes of the status
LED
indicator with the multiple sound signals of the Beeper will confirm the
saving, switch on the ignition to automatically save the settings and exit the
programming mode.
Level 10- Configuring system settings via the wireless interface
This function is under construction.
Level 11 – Programming and configuring «immobilizer PIN-code»
To programming «immobilizer PIN-code», enter the programming mode and
press
VALET
button 11 times. The level is divided into 3 sublevels (Sublevel
11.1 – Selecting the buttons; sublevel 11.2 entering PIN-code; sublevel 11.3 –
confirmation of the PIN-code input).
The system will automatically enter the sublevel 11.1 (selecting the buttons)
after entering the level 11. The system can determine the buttons via analog
«Code immobilizer» input or via digital protocol of a car. It is necessary to
configure the analog input (INP) as «Code immobilizer» in the settings of the
base unit inputs when implementing the «Code immobilizer» via analog input.
It may be necessary to switch on the ignition after entering the level 11 of
programming (if the car bus is active only when the ignition is switched on)
when implementing the «Code immobilizer» via digital car bus protocol.
After selecting active buttons enter the sublevel 11.2 (Entering PIN-code)
by pressing
VALET
button once. Program the PIN-code using selected buttons
at this sublevel; press
VALET
button once and enter the PIN-code again. To
confirm re-entering the PIN-code and save all the settings press
VALET
button
once again.
Sublevel 11.1 – Selecting the button:
This sublevel is used to select active buttons via digital protocol of a car or
via analog input «Code Immobilizer». To determine the activity of the analog
«Code Immobilizer» input, apply potential to the corresponding input (INP) of
the base unit,
LED
indicator will be flashing orange. If you determine buttons
via digital protocol select one or more buttons (up to four) for entering the
secret code of the immobilizer.
To do this press the selected button,
LED
indicator will confirm input with
orange flashes. If there are no orange flashes when any button is pressed, then
this button is not recognized by the system, select a different button. Repeat
the procedure to select the second, third, fourth button and enter the next
sublevel. To enter the next sublevel press
VALET
button once.
Sublevel 11.2 – Entering PIN-code:
Program immobilizer deactivation PIN-code using selected button or
buttons. Enter the first digit by pressing the previously selected button (pauses
between presses should not exceed 1 second). The base unit will confirm
entering with red flash of
LED
indicator. Enter the second (third, fourth) digit
by pressing the previously selected button. The base unit will confirm entering
of each digit with red flash of
LED
indicator.
Input the required number of digits (up to 4) and then press
VALET
button.
The system will confirm receiving of the secret validator code with long red
flash of
LED
indicator and will wait for confirmation of PIN-code.
Sublevel 11.3 - Confirmation of the PIN-code input:
Enter PIN-code again similarly to the procedure (level 11.2 – Entering PIN-
code) and press
VALET
button. The system will confirm correct PIN-code
with red and green flashes of
LED
indicator and will memorize PIN-code,
then will proceed to the programming mode awaiting level input. Incorrect
confirmation is indicated with long red flash of
LED
indicator, after that the
system will return to a programming mode
Level 15 – Disabling/enabling of immobilizer tag
To disabling/enabling of immobilizer tag enter the programming menu and
press
VALET
button 15 times. The
LED
indicator will light green (green light
indicates enabled tag) and the system will wait for the «Secret code» entering.
Red light of
LED
and 5-second sound signal of the Beeper indicates disabled
immobilizer tag.
Disabling radio tag:
The system will wait 10 seconds for entering the «Secret PIN-code». If
the PIN-code is not entered within 10 seconds, the system will return to the
programming menu. Enter the «Secret PIN-code» that is written on the owner’s
plastic card. The system will confirm disabling of the radio tag with two sound
signals of the siren and the series of the sound signals of the Beeper. After that
the system will return to the programming menu. Switch on the ignition to exit
programming mode
