background image

65

64

USER MANUAL

PANDORA DXL 1090L SERVICE-SECURITY SYSTEM

A D D I T I O N A L   I N F O R M A T I O N

SIREN SOUNDS AND TURN LIGHT SIGNALS

Signal name

Signal Description

Alarm mode, PANIC mode

Incessant sound and light signals for 30 sec

Arming

1 sound /1 light signals

Disarming

2 sound / 2 light signals

«Sensors triggered»signal when 

disarming

4 sound / 4 light signals

«Sensor malfunction» signal when 

arming

4 sound / 4 light signals

Sensor warning level triggered 

3 sound signals

Car search

5 sound / 5 light signals

MEANING OF LED INDICATOR COLORS

Indicator status

Meaning

Short red flashes

The system is armed

Lit red

The system is preparing for automatic arming

Orange flash

Confirms VALET button press

Orange flashes

Confirms a number of recorded remote controls (when 

switching on ignition)

Green flashes

Confirms a number of recorded remote controls (when 

switching on ignition

Red flash

Confirms a recorded mobile device (when switching on ignition)

Red and green flashes

PIN-code confirmed

Faded

The system is disarmed

A D D I T I O N A L   I N F O R M A T I O N

CHECKING THE NUMBER OF RECORDED REMOTE CONTROLS/

RADIO TAGS/MOBILE DEVICE

The number of recorded remote controls/tags and registered mobile device can be checked 

by the number of orange, green and red flashes of 

LED

 indicator. Number of registered 

remote controls/tags/mobile device can be checked every time the ignition is switched on 

when the system is disarmed. The number of orange 

LED

 flashes will indicate the number 

of recorded remote controls, the number of green 

LED

 flashes will indicate the number of 

recorded remote controls following red flash will indicate registered mobile device.

You can also check the number of recorded tags and registered mobile device by 

taking off and putting back on battery terminal. The system will emit short sound 

signals from a siren with less than 1 sec. interval. The number of the signals equals to 

the number of recorded remote controls. After a pause of 2 seconds the system will 

emit short sound signals from a siren with less than 1 sec. interval. The number of the 

signals equals to the number of recorded radio tags. After a pause of 2 seconds the 

system signal will indicate registered mobile device.

WARRANTY OBLIGATIONS

Manufacturer guarantees correct operation of the service-security system if exploitation, 

installation, storage and transportation conditions described in this manual were met.

The system should only be used according to installation scheme and user manuals.

The system is meant to be installed by the professional car electronics installers. 

We recognize that outside Russia the system can be installed by amateurs – those 

installations are still a subject of limited warranty. The installer should fill in installation 

certificate that is included in this manual.

Summary of Contents for DXL 1090L




































Reviews: