background image

11

10

USER MANUAL

PANDORA DXL 1100L SERVICE-SECURITY

TURNING ON/OFF THE REMOTE CONTROL

To turn the remote control on, press and hold  

  button. 

«REMOTE ON»

 ringtone 

will play. Pressing and holding this button again for 3 seconds will cause the remote 

to turn off.

MEANING OF THE REMOTE CONTROL LED INDICATORS

Green light indicator:

• Flashes if there is a connection with the base unit

• Goes dark when there is no connection with the base unit.

Red light indicator:

• Flashes frequently if there is any notification.

• Flashes occasionally when there is no connection.

R E M O T E   C O N T R O L

 

WARNING! ALL CONTROL COMMANDS ARE TRANSMITTED VIA 

RADIO CHANNEL, FOR MAXIMUM EFFECTIVENESS AND RANGE IT IS 

RECOMMENDED NOT TO SHIELD AERIAL AREA (SEE PICTURE) WITH FINGERS 

WHEN USING A REMOTE CONTROL.

   

REMOTE CONTROL IS UNIFIED CONTROL DEVICE. REMOTE CONTROL 

FUNCTIONS DEPEND ON SECURITY SYSTEM MODEL

System is disarmed

System is armed

(no alarm events)

Ignition is switched on Ignition is switched off

  

(short press)

Arming with sound 

confrmation

Search mode – flashes 

of turn signals with 

sound signals for 5 

seconds

  

(1 sec)

Arming without sound 

confrmation

Search mode – flashes 

of turn signals without

sound signals for 5 

seconds

  

(2 sec)

Switch on ‘Ignition 

maintenance’ mode

  

(3 sec)

Remote engine start

 

(short press)

Disarming with sound 

confirmation

 

(1 sec)

Disarming without 

sound confirmation

(>2 sec.)

Switch off ‘Ignition 

maintenance’ mode

Switch off the ignition 

during remote or 

automatic engine start 

procedure.

QUICK ACCESS FUNCTIONS OF THE REMOTE CONTROL

R E M O T E   C O N T R O L

Summary of Contents for DXL 1100L


























Reviews: