29
28
U S E R M A N U A L
P A N D O R A D X L 1 9 2 0 L / 1 9 3 0 L C A R S E R V I C E - S E C U R I T Y S Y S T E M
confirm the resetting to the factory settings with a long red flash of LED indicator. After that the system
will return to a programming mode.
Level 5 – Recording Bluetooth engine compartment module
To record a Bluetooth engine compartment module, enter programming mode and press
VALET
button 5 times. The
LED
indicator will light green and the system will enter the recording of an engine
compartment module mode. Connect the module in accordance with installation manual. The system
will confirm the registration with a short sound signal.
Saving changes:
To finish the recording of the engine compartment module,
VALET
button should be pressed once
again, the series of red and green flashes of the status
LED
will confirm the saving, switch on the ignition
to automatically save the settings and exit programming mode.
Levels 6, 7 – Recording Bluetooth radio relays
Radio relays recording is performed one by one starting from the 6 level: radio relay №1
is recorded on the 6 level; radio relay №2 is recorded on the 7 level. The radio relay can be
overwritten only on the level of its initial registration.
To record Bluetooth radio relays №1, №2, enter programming mode and press
VALET
button 6 times
for radio relay №1 or 7 times for radio relay №2.
LED
indicator will light green and the system will enter
the recording of a radio relay mode. Connect a relay in accordance with installation manual. The system
will confirm recording with a short sound signal.
Saving changes:
To finish the recording of the Bluetooth radio relay,
VALET
button should be pressed once again, the
series of red and green flashes of the status
LED
indicator will confirm the saving, switch on the ignition
to automatically save the settings and exit the programming mode.
Level 10 – Configuring system settings via the wireless interface
This function is under construction.
Level 11 – Programming and configuring “Immobilizer code“
To program the “Immobilizer code“, enter the programming mode and press
VALET
button 11
times. The level is divided into 3 sublevels (Sublevel 11.1 – Selecting buttons; sublevel 11.2 entering
PIN-code; sublevel 11.3 – confirmation of the PIN-code input).
The system will automatically enter the sublevel 11.1 (Selecting buttons) after entering the level 11.
The system can determine buttons via analog “Code immobilizer” input or via digital protocol of a car.
It is necessary to configure an analog input (INP) as “Code immobilizer“ in the settings of the base unit
inputs when implementing the “Code immobilizer” via an analog input. It may be necessary to switch on
the ignition after entering the level 11 of programming (if the car bus is active only when the ignition is
switched on) when implementing the “Code immobilizer” via digital car bus protocol.
After selecting active buttons enter the sublevel 11.2 (Entering PIN-code) by pressing
VALET
button
once. Program PIN-code using selected buttons at this sublevel; press VALET button once and enter PIN-
code again. To confirm PIN-code re-entering and save all the settings press
VALET
button once again.
Sublevel 11.1 – Selecting buttons:
This sublevel is used to select active buttons via digital protocol of a car or via “Code Immobilizer“
analog input. To determine the activity of the analog “Code Immobilizer“ input, apply potential to the
corresponding input (INP) of the base unit,
LED
indicator will be flashing orange.
If you determine buttons via digital protocol select one or more buttons (up to four) for entering
the secret code of the immobilizer. To do this press the selected button,
LED
indicator will confirm input
with orange flashes. If there are no orange flashes when any button is pressed, then this button is not
recognized by the system, select a different button. Repeat the procedure to select the second, third,
fourth button and enter the next sublevel. To enter the next sublevel press
VALET
button once.
Sublevel 11.2 - Entering PIN-code:
Program immobilizer deactivation PIN-code using selected button or buttons. Enter the first digit by
pressing the previously selected button (pauses between presses should not exceed 1 second). The base
unit will confirm entering with red flash of
LED
indicator. Enter the second (third, fourth) digit by pressing the
previously selected button. The base unit will confirm entering of each digit with red flash of
LED
indicator.
Input the required number of digits (up to 4) and then press
VALET
button. The system will confirm
receiving of the secret validator code with long red flash of
LED
indicator and will wait for confirmation
of PIN-code.
Sublevel 11.3 - Confirmation of the PIN-code input:
Enter PIN-code again similarly to the procedure (level 11.2 – Entering PIN-code) and press
VALET
button. The system will confirm correct PIN-code with red and green flashes of
LED
indicator and will
memorize PIN-code, and then the system will proceed to programming mode awaiting level input.
Incorrect confirmation is indicated with long red flash of
LED
indicator, after that the system will return
to programming mode.
Level 15 – Disabling/enabling immobilizer tag
To disabling/enabling of immobilizer tag, enter programming menu and press
VALET
button 15
times.
LED
indicator will light green (green light indicates enabled tag) and the system will wait for the
“Secret PIN-code” entering. Red light of
LED
indicates disabled immobilizer tag.
Disabling radio tag:
LED
indicator will light green after entering the programming level. The system will wait for entering
the “Secret PIN-code“. Enter the “Secret PIN-code“ that is written on the owner’s plastic card. The system
will confirm disabling of the radio tag with two sound signals of the siren and a long red
LED
flash. After
