11
10
U S E R M A N U A L
P A N D O R A D X L 1 9 2 0 L / 1 9 3 0 L C A R S E R V I C E - S E C U R I T Y S Y S T E M
Emergency disarming using «VALET» button
In case you cannot disarm the system using a phone or immobilizer
tag, the “Secret PIN-code“ can be used. The “Secret PIN-code“ is
written on the owner’s plastic card under protective layer. Erase
the protective layer and use
VALET
button to input the PIN-code.
The code must be entered only when the base unit is powered
and the ignition is switched off. The PIN-code can be entered using
external or located on the base unit
VALET
button. The digits
input and correct input is indicated by the external or located on
the base unit
LED
indicator.
Entering the PIN-code:
Enter the first digit of the code using VALET button. Press
the button a number of times, equals to the first digit. Pauses
between presses should not exceed 1 second. Each pressing will
be confirmed with an orange
LED
indicator flash. A Pause for
more than 1 second and a red
LED
indicator flash confirm the
input of the first digit. Then you can enter the next digit.
• Enter the second digit of the code using
VALET
button. Press
the button a number of times, equals to the second digit. Pauses
between presses should not exceed 1 second. Each pressing will be confirmed with an orange
LED
indicator
flash. A Pause for more than 1 second and a red
LED
indicator flash confirm the input of the second digit.
Then you can enter the next digit.
• Enter the third digit of the code using
VALET
button. Press the button a number of times, equals
to the third digit. Pauses between presses should not exceed 1 second. Each pressing will be confirmed
with an orange
LED
indicator flash. A Pause for more than 1 second and a red
LED
indicator flash
confirm the input of the third digit. Then you can enter the next digit.
• Enter the fourth digit of the code using
VALET
button. Press the button a number of times, equals
to the fourth digit. Pauses between presses should not exceed 1 second. Each pressing will be confirmed
with an orange
LED
indicator flash. The system will confirm correct PIN-code with the series of red and
green flashes and the system will be disarmed. If the input was incorrect, it will be indicated with a red
LED
indicator flash and the system will stay in a previous state. New input can be attempted after 5 seconds.
If the system was disarmed and the ignition was switched off it will enter programming mode after
correct input of the PIN-code.
For emergency arming when the ignition is switched off, press and hold
VALET
button for 3 seconds.
The system will be armed in 30 seconds. Status
LED
indicator is lighting red during the countdown.
Enabling/Disabling immobilizer radio tag
Write down or remember the “Service PIN-code“
To disable immobilizer radio tag, enter level 15 (the system should be in programming mode). Enter the
“Secret PIN-code“ to disable radio tag or press
VALET
button once to enable radio tag.
Enter the “Service PIN-code” to enter programming mode (factory preset of the service PIN-code
is “1-1-1-1“). You can enter the code only if the base unit is powered, the ignition is switched off, the
system is disarmed and the maintenance mode is switched off. If there is no “Service PIN-code“, you
can enter programming mode using the “Secret PIN-code“ written on the owner’s card. After entering
programming mode, press
VALET
button 15 times. Green color of
LED
indicator means a radio tag is
switched on, red color means a radio tag is switched off.
Disabling radio tag:
LED
indicator will light green after entering the programming level. The system will wait for entering
the “Secret PIN-code“. Enter the “Secret PIN-code“ that is written on the owner’s plastic card. The system
will confirm disabling of the radio tag with two sound signals of the siren and a long red
LED
flash. After
that the system will return to the programming menu. If the PIN-code is not entered within 10 seconds
or the input is incorrect, a siren will sound one signal,
LED
will produce the series of red and green
flashes and the system will return to the programming menu.
WARNING! MAKE SURE THAT A PROTECTIVE LAYER ON THE OWNER’S PLASTIC
CARD IS INTACT AFTER THE INSTALLATION OF THE SYSTEM. THE PLASTIC CARD
HOLDS THE “SECRET PIN-CODE“.
WARNING! CAREFULLY REMOVE THE PROTECTIVE LAYER, DO NOT USE SHARP OB-
JECTS TO AVOID DAMAGING OF HIDDEN INFORMATION UNDER A PROTECTIVE
LAYER.
2-2-2-2
PIN
Three-color status
LED indicator (green,
red, orange)
VALET button
WARNING!
IT IS HIGHLY RECOMENDED TO CHANGE FACTORY PRESET OF THE “SERVICE
PIN-CODE” FOR IMPROVING SECURITY OF THE SYSTEM.
