background image

© Panduit Corp. 2017 

OPERATION MANUAL

 

CT-902HP 

FAMILY

 

 

Page: 6 of 6 

PREVENTIVE MAINTENANCE 

Maintenance should be performed monthly, whenever possible damage has occurred, or as often as operating 
conditions warrant. 

 

1.  Operate  CT-902HP  pump on 110 volts AC only,  or voltages between 95 and 120.  Do not operate pump on 

voltages less than 95 volts, or on DC current. 
Operate CT-902HP220 pump on 220 volts AC only, or voltages between 200 and 242.  Do not operate pump on 
voltages less than 200 volts, or on DC current. 

 
2.  Level of oil is to be maintained above the red dot in center of port window.  To add oil, unscrew entire oil vent 

fitting from tank with a wrench.  Using a funnel, pour oil into the tank opening.  Recommended hydraulic oil: 
Shell Tellus Hydraulic Oil S2 V 15 or approved equivalent.  Replace fitting. 

 
3.  When attaching hoses, be sure all couplers are securely fastened.  Always keep couplers clean by wiping oil 

and debris from surfaces before connecting hoses to pump or tool. 

 
4.  Never move pump by pulling on the electrical cords. 
 
5.  Always store pump with the air vent in the closed position. 

 
 

TROUBLESHOOTING  

If system locks up under pressure, perform the following steps: 

 

 

Verify that the solenoid on pump is making an audible “click”. 

 

If above step checks out, determine which fitting needs to be tightened. 

 

When pump is released, does the hose stay rigid or flex back down? 

 

If the hose stays rigid, the problem is in the connection from pump to hose. 

 

If the hose flexes down, the problem is in the connection from hose to tool head. 

 

To tighten couplers, use channel lock pliers or pipe wrench; (wrap couplers to avoid causing damage). 

 

When you feel the couplers tighten, depress the release on the pump; (pressure should be released). 

 

Tool head should retract.  Finish tightening couplers by hand. 

 
 

CONTACT INFORMATION  •  For Technical Support: 

Panduit USA, Tinley Park, IL 
USA Tel: 1-800-777-3300 
Website: www.panduit.com  
E-mail: techsupport@panduit.com 

Panduit Canada Headquarters 
Markham Ontario, Canada 
Canada Tel.: 905-475-6922 or 800-387-9689 
Fax.: 905-475-6998 
Website: www.panduit.com  
E-mail: cs-tp-canada@panduit.com 

Panduit Latino America, Guadalajara, 
Jalisco, Mexico 
Latino America Tel.: 52 (333) 666 2501 
Fax.: 52 (333) 666 2510 
Website: www.panduit.com  
E-mail: cs-la@panduit.com 

Panduit China, Beijing 
Xuanwumen Xidajie Xicheng District 
Beijing, China  
Tel: 8610 6641 0371  •  Fax: 8610 6641 0375 
Toll Free Customer Service - North China: 10800 
6500 211  •  South China: 10800 2650 211 
E-mail: cs-ap@panduit.com 

Panduit Singapore – Sales Office 
Singapore, Republic of Singapore  
Tel: 65 6379 6700  •  Fax: 65 6379 6759 
E-mail: cs-ap@panduit.com 

 

 
 

Summary of Contents for CT-902HP








Reviews: