(A) Set Fusion Condi
�
on
(B) Perform Arc Test
(9) Set ribbon
fi
ber on Fiber holder.
(10) Remove Coa
�
ng (JR-6)
1. Place
3. Slide
Clean rubber clamp
and blade regularly
(12) Cleave the
fi
ber (FC-6M)
No gap
(13) Set
fi
ber holder on the splicer
(le
�
side).
2. Close
Place
fi
ber on
V-groove gently
See the opera
�
on manual for your splice machine.
Spring
(Remove from
Front Parts)
Protec
�
on
Sleeve
CH1 Fiber
Front Side
Stainless Steel
Bo
�
om Side
Make sure the
orienta
�
on of Sleeve
CH1 Fiber
Front Side
＞
25mm
(11) Fiber Cleaning.
Moistened
with alcohol
(1) Slide Rear Parts onto
the cord.
(2) Mark at 150mm from the end
of the cord.
(3) Mark Slit by LYNX2-CORDTOOL-2&3.
Set the cord on “3mm” groove.
Set the marking point
at the edge of top
(4) Fold the slit outer sheath and Kevlar
backward. Hold them by a mending tape.
(8) Slide Rear Parts, Spring and Protec
�
on
Sleeve onto the ribbon
fi
ber.
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12
Method A
End A
BL
OR
GR
BR
SL
WH
RD
BK
YL
VI
PK
AQ
End B
BL
OR
GR
BR
SL
WH
RD
BK
YL
VI
PK
AQ
Method B
End A
BL
OR
GR
BR
SL
WH
RD
BK
YL
VI
PK
AQ
End B
AQ
PK
VI
YL
BK
RD
WH
SL
BR
GR
OR
BL
Method C
End A
BL
OR
GR
BR
SL
WH
RD
BK
YL
VI
PK
AQ
End B
OR
BL
BR
GR
WH
SL
BK
RD
VI
YL
AQ
PK
Another
(ex. Corning)
End A
BL
OR
GR
BR
SL
WH
RD
BK
YL
VI
PK
AQ
End B
AQ
PK
VI
YL
BK
RD
WH
SL
BR
GR
OR
BL
Table 1. Fiber Alignment. (See Appendix.)
(5) Fiber standing in line according to Table 1.
(6) Ribbon Processing.
1. Apply Adhesive
2. Use sponge to spread adhesive evenly
3. Move a slide stage
No Bending
No gap between
fi
bers
4. Comple
�
on
130mm
>30mm
(7) Cut the
fi
ber to be 130mm and con
fi
rm the
length of ribbonized is 30mm or more.
Ribbon End
Marking
Marking
Push “power
key” for more
than 1 sec.
Arc Test “ON”.
Then perform the arc test
according to the instruc
�
on.
*Fiber for tes
�
ng is included
in the kit.
Please check
fi
ber type
inside the
fi
eld
fi
ber.
“Main Menu”
Select Fiber Type
Select “Fiber Type”, then “Return”.
“Main Manu”
Select Sleeve Type
Select Sleeve Type
Then “Return”
For 8c
For 12c
No Bending
No Gap Between Fibers
For Technical Support: www.panduit.com/resources/install_maintain.asp
© Panduit Corp. 2019
FS148
Page 4 of 5
INSTALLATION INSTRUCTIONS
