background image

 

 

 

 

                                                               www.panel.it                                                                25 

 

 

25 

 

Chapter 7: maintenance

 

 

This chapter describes service/maintenance work that can be carried out by a qualified end user. 
Only skilled staff must make any job on the device and only after having fully read and understood the 
safety instructions (chapter 1.1). 

 

 

7.1  Cleaning

 

 

Warning! 
This device must be switched off before cleaning in order to prevent unintended functions from being triggered when 
handling the touch screen or pressing keys.  

 

This device should be cleaned with a moist cloth. The cloth should be moistened with water and detergent, a screen 
cleaning agent or alcohol (ethanol). 
The cleaning agent should be applied to the cloth beforehand, not sprayed directly on the device! 
Aggressive solvents, chemicals, scouring agents, pressurized air or steam jets should never be used. 

 
 

7.2  Lithium battery

 

 

The  Lithium  battery  adopted  on  this  motherboard  contains  Perchlorate,  a  toxic  substance  controlled  in  Perchlorate 
Best Management Practices (BMP). When you discard the Lithium battery in California, USA and the rest of the world, 
please follow the related regulations in advance. 

 
 

7.3  Spare parts

 

 

It is recommended to install only original Panel spare parts. 
If the customer mount not original spare parts, we c

an’t grant 

the correct work of the device. 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for PVR-EM Series


























Reviews: