background image

OPERATING TIPS

It is not necessary to disconnect the steering rod from the kicker ball stud or T‐4 when  l ng your kicker 
engine.  The quick disconnect will automa cally move into the correct posi on.  

However, it is highly recommended that when using your main engine that you disconnect the steering arm 
from the kicker ball stud.  The kicker engine has a tendency to shi  from side to side when running your main 
engine or when trailering.  This movement may be enough to put addi onal stress on the steering arm or ball 
stud.  The simple and easy way to prevent your steering arm from being damaged when running or trailering is 
to disconnect both ends from the ball studs and store the rod in a convenient loca on. If this solu on is used, 
the drive rod 

MUST 

 be securely threaded on to the T‐4.

 

Another op on is to purchase an addi onal ball stud and mount it on your transom deck. A ach the loose end 
that you have disconnected from the kicker to the ball stud mounted on the transom.  

WARNING

NEVER STAND ON OR PUT DOWNWARD PRESSURE ON THE T‐4 

BODY.  IT CANNOT BE USED AS A STEP OR RESTING PLACE FOR 
YOUR FOOT WHILE FISHING. 

MAINTENANCE 

The following is a list of items to do periodically to insure the longevity of your 

T‐4

1. Frequently check the moun ng nut holding the T‐4 to your motor. Tighten as necessary.

2. Frequently check the ball studs.  Make sure they are  ght.

3. Depending on use, grease the T‐4 as least once a year. 1 to 2 pumps of grease  in the zerk is sufficient.

4. Clean the drive rod at least once a month with a clean cloth and reapply a light coa ng of grease once it is

clean.

5. Make sure electrical connec ons are  ght, re‐apply dielectric grease as necessary

If you need replacement parts, go to the MarineTech Products website and look for the “SHOP FOR PARTS” 
tab at the top of the page.  Once at the Parts Shop, click on Panther‐ ElectroSteers. 

Summary of Contents for Freshwater 55-0102










Reviews: