background image

Safety hints

 

 

1. Do not start operating the System until you have read and understood the 
operating instruction. All safety hints, information on measures and weights, 
as well as on maintenance intervals have to be observed. 
 
2. The Panther JibGlider may only be operated by competent staff. 
PANTHER regularly offers training seminars, in which participants receive a 
certificate after successfully completing the training. For further information 
and dates please contact us under +49 89 613 900 01. 
 
3. Lifting, swiveling and drive area of the JibGlider including accessories have to 
be kept free in any case. Possible danger of bruises. 

The safety zone of 

≥ 

0,5 m must be kept free in all directions. 

 
4. Please observe that there is a danger of tilting whenever you mount any 
equipment on the Panther JibGlider. 
 
5. Attention: do not use the JibGlider on inclined planes or in vehicles
By means of brakes or other devices the Panther JibGlider has to be secured 
against unintended movements. The subsoil needs to be firm and unyielding. 
A minimum payload of 200 kg/m² is required of the subsoil. 
 
6. Repair works should only be executed by the manufacturer or by well-trained 
staff. PANTHER is offering training seminars, which can be held according to 
agreement. For further information please call +49 89 613 900 30 (Panther 
Service Department). 
 
7. Make sure that unauthorized personnel can not use the JibGlider if it is out 
of order. 
 

Summary of Contents for JibGlider System











Reviews: