Panther PA-420C, Installation Manual

128-9239

9 of 24

Page 9

    long chirp and 2 Light flashes when the key is turned on indicates that you are in
    feature selection of bank 2.
4. Press the pushbutton switch 1 time to access the first selection as shown below.
    Use the button of the transmitter to change the feature selection or press the
    pushbutton to advance to the next selectable feature.

Bank 2

Feature

               1 Chirp/Flash     2 Chirp/Flash    3 Chirp/Flash    4 Chirp/Flash    5 Chirp/Flash    6 Chirps/Flash

     Default

1stDoor Unlock             1S/1S                    3.5 S/3.5S         1 S/Dbl 1 S.        Dbl 1/1 S           Dbl 1/Dbl 1        1S L/350mS ul

      1S

2nd Accy Lock                NA

3rd Accy. UL                On

                  Off

      Off

4th Horn Chirp              10mS                  16mS                   30mS

    40mS

       50mS

      16mS

5

th

 Chp Del TX              NA

6th Park Lights              Normal               NA                       On 15 Sec W/UL

      Normal

5. When finished setting the keyless/alarm selectable features, turn the ignition off then
    on to advance to Bank 3, Remote Start Selectable Features.
    1 Flash when the key transitions off, then 2 long chirps and 3 light flashes when the key
    transitions on.
6. Press the pushbutton switch one time to access the first selection as shown below.
    Use the button of the transmitter to change the feature selection or press the
    pushbutton to advance to the next selectable feature.

Bank 3

Feature

                1 Chirp/Flash      2 Chirp/Flash     3 Chirp/Flash   4 Chirp/Flash    5 Chirp/Flash    6 Chirps/Flash

Default

1 RF Start Chirp            Off                     On

On

2 Run Time

                5 Min.                 10 Min.                   15Min.              20 Min.

10 Min

3 Park Lights                 On Steady           Flash

Steady

4 Input Check                 Voltage               Tach

DBI  Tach 

Hybrid

Tach

5 Voltage Level               > 0.5V B4 Start   < 0.5V B4 Start

> 0.5

6 Ign. 2 Select               Off With Crank    On With Crank    Same As Accy                                                                                                 On With Crank

7 Diagnostics               Off                         On

Off

8 Crank Time                 0.8Sec                 1.0 Sec

1.5 Sec             2.0 Sec               3.0 Sec                      4.0 Sec                     1.0 Sec

9 Gas/Diesel                 Gas                       Diesel 10

Diesel 15          Diesel 20

Gas

10 Grn/Blk (Aux O/P)  Single Pulse          As D U/L Pulse

Single

11 DBI Select                ADS                      DBI

ADS

12 Time Start                2 Hours                 4 Hours

4 Hours

Diagnostics:

Enter Bank 3 and turn on selectable feature # 7 as described in the feature selection and
setting section.
Exit the feature selection mode then press and hold the pushbutton valet/program switch
and then turn the ignition switch to the on position.

NOTE:

Diagnostic mode is a temporary mode. Once you have accessed the diagnostic
mode, the unit will pause for two seconds then begin to flash the last stored shut
down code. This code will be displayed three times in succession, then the unit
will automatically exit the diagnostic mode.

The parking lights will flash a number of times indicating the reason for the last remote
start shutdown. The light flash indications are as follows:
1 Flash

Run timer expired

2 Flashes

Low or no tach signal (RPM)

3 Flashes

Positive inhibit wire activation

5 Flashes

RF shutdown signal received, or manual start trigger wire reactivated.

6 Flashes

High tach signal (RPM)