Para systems ED1000RM2U, User Manual

22

23

English

English

IF THE UPS REQUIRES SERVICE

1. Use the TROUBLESHOOTING section to eliminate obvious causes.
2. Verify there are no circuit breakers tripped.  A tripped circuit breaker is the
    most common problem.
3. Call your dealer for assistance.  If you cannot reach your dealer, or if they
     cannot resolve the problem call or fax MINUTEMAN Technical Support at
     the following numbers; Voice phone (972) 446-7363, FAX line (972) 446-
     9011 or visit our Web site at www.minutemanups.com the "Discussion
     Board".  Please have the following information available BEFORE calling
     the Technical Support Department.

 A. Your name and address.
 B. Where and when the unit was purchased.
 C. All of the model information about your UPS.
 D. Any information on the failure, including LEDs that may be illuminated.
 E. A description of the protected equipment, including model numbers if pos-

 sible.

 F. A technician will ask you for the above information and, if possible, help

         solve your problem over the phone.  In the event that the unit requires

      factory service, the technician will issue you a Return Material Authoriza-

        tion Number (RMA #).

 G. If the UPS is under warranty, the repairs will be done at no charge.  If not,

 there will be a charge for repair.

4. Pack the UPS in its original packaging.  If the original packaging is no longer

 available, ask the Technical Support Technician about obtaining a new set.
 It is important to pack the UPS properly in order to avoid damage in transit.
 Never use Styrofoam beads for a packing material.
 A. Include a letter with your name, address, day time phone number, RMA

  number, a copy of your original sales receipt, and a brief description of the
  problem.

5. Mark the RMA # on the outside of all packages.  The factory cannot accept

 any package without the RMA # marked on the outside.

6. Return the UPS by insured, prepaid carrier to:

Para Systems Inc.
MINUTEMAN UPS

1455 LeMay Drive

Carrollton, TX 75007

ATTN: RMA # _______

Default: 120VAC (208VAC), User selectable: 110VAC (240VAC)

1500VA/1200W

1000VA/800W

Protection

Waveform Type

Over-Current, Short-Circuit Protected and Latching Shutdown

True Sine Wave

Frequency

50/60Hz, +/-0.1Hz (unless synchronized to utility)

Nominal Voltage

Maximum Power Capacity

0 ms

>87% (Full Load)

Resettable Circuit Breaker

50 or 60 Hz, +/-6Hz, autosensing

0 - 150VAC (0 - 300VAC)

90 - 138VAC (160 - 280VAC)

120VAC: 117.6 - 122.4VAC (208VAC: 204 - 212VAC)

Transfer Time

Efficiency (Line Mode)

Input Protection

Frequency Limits

Voltage Range

Acceptable Input voltage

ED1500RM2U

ED1500RMT2U

ED1000RM2U

ED1000RMT2U

Model Number

SYSTEM SPECIFICATIONS

Voltage Range

Topology

Double Conversion On-Line, True Sine Wave

OUTPUT ON-LINE OPERATION

INPUT

Number of Phase

Single (1

∅

2W +G)

Nominal Voltage

120VAC (208VAC)

Low Voltage Transfer Point 80/90V (160V) resets to Utility Power at 86/96V (170V) or higher

High Voltage Transfer Point

138V (280V) resets to Utility Power at 132V (270V) or lower

Voltage Regulation

N/-2%

Frequency Range

60Hz: 54 - 66Hz or 50Hz: 44 - 56Hz

OUTPUT BATTERY OPERATION

Voltage Regulation

N/-2% (until Low Battery Warning)

Voltage T.H.D.

<3% (Linear Load)

+/-5% @ 100% Load change in 30 ms

Dynamic Response

Slew Rate

<1Hz / second

Overload Capacity

>115% - <125% for 60-seconds
>125% - <150% for 30-seconds
>150% for 1-second

ED2000RM2U

ED2000RMT2U

ED3000RM2U

ED3000RMT2U

2000VA/1600W 3000VA/2100W

80 - 138VAC
(160 - 280VAC)

Power Factor Correction

>97% at Full Load

Crest  Factor

3 : 1