background image

 

40

9 Obtaining 

Service 

 
9.1.1 

Use the troubleshooting section to eliminate obvious causes. 

9.1.2 

Verify there are no circuit breakers tripped. A tripped circuit breaker is the 

most common problem. Call your dealer for assistance. If you cannot reach 
your dealer, or if they cannot resolve the problem call or fax MINUTEMAN 
Technical Support at the following numbers; Voice phone (972) 446-7363, 
FAX line (972) 446-9011 or visit our Web site at www.minutemanups.com 
the "Discussion Board". Please have the following information available 
BEFORE calling the Technical Support Department. 

a.  Your name and address. 
b.  Where and when the unit was purchased. 
c.  All of the model information about your unit. 
d.  Any information on the failure. 
e.  A technician will ask you for the above information and, if possible, help 

solve your problem over the phone. In the event that the unit requires 
factory service, the technician will issue you a Return Material 
Authorization Number (RMA #). 

f.  If the unit is under warranty, the repairs will be done at no charge. If not, 

there will be a charge for repair. 

9.1.3 

Pack the unit in its original packaging. If the original packaging is no longer 

available, ask the Technical Support Technician about obtaining a new set. 
It is important to pack the unit properly in order to avoid damage in transit. 
Never use Styrofoam beads for a packing material. 

a.  Include a letter with your name, address, daytime phone number, RMA 

number, a copy of your original sales receipt, and a brief description of 
the problem. 

b.  Mark the RMA # on the outside of all packages. The factory cannot 

accept any package without the RMA # marked on the outside. 

9.1.4 

Return the unit by insured, prepaid carrier to: 

 
 

Para Systems Inc. 

MINUTEMAN UPS 

1455 LeMay Drive 

Carrollton, TX 75007 

ATTN: RMA #   

 

 
 
 

 

41

10 Limited Product Warranty 

 

Para Systems, Inc. (Para Systems) warrants this equipment, when properly applied 
and operated within specified conditions, against faulty materials or workmanship 
for a period of three years from the date of purchase. For equipment sites within the 
United States and Canada, this warranty covers repair or replacement of defective 
equipment at the discretion of Para Systems. Repair will be from the nearest 
authorized service center. Replacement parts and warranty labor will be borne by 
Para Systems. For equipment located outside of the United States and Canada, 
Para Systems only covers faulty parts. Para Systems products repaired or replaced 
pursuant to this warranty shall be warranted for the un-expired portion of the 
warranty applying to the original product. This warranty applies only to the original 
purchaser who must have properly registered the product within 10 days of 
purchase. 
 
The warranty shall be void if (a) the equipment is damaged by the customer, is 
improperly used, is subjected to an adverse operating environment, or is operated 
outside the limits of its electrical specifications; (b) the equipment is repaired or 
modified by anyone other than Para Systems or Para Systems-approved personnel; 
or (c) has been used in a manner contrary to the product’s User's Manual or other 
written instructions. 
 
Any technical advice furnished before or after delivery in regard to use or 
application of Para Systems’ equipment is furnished without charge and on the 
basis that it represents Para Systems’ best judgment under the circumstances, but 
it is used at the recipient’s sole risk. 
 
Except as provided herein, Para Systems makes no warranties, expressed or 
implied, including warranties of merchantability and fitness for a particular purpose. 
Some states do not permit limitation of implied warranties; therefore, the aforesaid 
limitation(s) may not apply to the purchaser. 

 

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL PARA SYSTEMS BE 
LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR 
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, 
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, Para 
Systems is not liable for any costs, such as lost profits or revenue, loss of 
equipment, loss of use of equipment, loss of software, loss of data, cost of 
substitutes, claims by third parties, or otherwise. The sole and exclusive remedy for 
breach of any warranty, expressed or implied, concerning Para Systems’ products 
and the only obligation of Para Systems hereunder, shall be the repair or 
replacement of defective equipment, components, or parts; or, at Para Systems’ 
option, refund of the purchase price or substitution with an equivalent replacement 
product. This warranty gives you specific legal rights and you may have other rights, 
which vary from state to state. 

 

Summary of Contents for Minuteman ED10000T
























Reviews: