background image

32

NOTES:

LIMITED WARRANTY

ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY.

1. LIMITED WARRANTY ON FRAME AND WELDS.  If the frame of the ParaBody product or a weld should crack or break, it will be repaired

or replaced by ParaBody.  Terms:  Lifetime – for so long as the Customer owns the ParaBody product.

2. LIMITED WARRANTY ON PARTS.  If the following parts are defective in material or workmanship, ParaBody will supply replacement parts:

all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad
shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger, spring
and knob. Terms:  Lifetime – for so long as the Customer owns the ParaBody product.

3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY.  If the coated cables or upholstery are defective in material or workmanship,

ParaBody will repair or replace them, at its option.  Terms:  Three (3) years.

4. CONDITIONS AND EXCEPTIONS.  Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized

ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of
ParaBody will void this Limited Warranty.

5. REPLACEMENT AND REPAIR EXPENSES.  ParaBody will provide only replacement parts or repair under this warranty.  The Owner is

responsible for all other costs.  Such costs may include, but are not limited to:  a. labor charges for service, removal, repair or reinstallation
of the ParaBody product or any component part;  b. shipping, delivery, handling and administrative charges for returning parts to ParaBody;
and c. all necessary or incidental costs related to installation of the replacement parts.

6. SHIPPING.  If shipping by the Owners is deemed necessary (in sole discretion of ParaBody), parts should be shipped in their original carton

or equivalent packaging, fully insured with shipping charges prepaid.  ParaBody will not assume any responsibility for any loss or damage
incurred in shipping.

7. CLAIM PROCEDURES.  If service on your ParaBody product is required during the warranty period, please contact our Customer Service

Department at 1-800-328-9714 for instructions regarding returning or replacing parts.  Please have available the following information:  (i) the
dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly
drawing included with your assembly instruction); (iv) a description of the nature of the problem.

8. OWNER’S RIGHT.  This Limited Warranty gives you specific legal rights.  You may also have other rights, which vary depending on local law.

9. LIMITATION OF IMPLIED WARRANTIES.  All implied warranties, except to the extent prohibited by applicable law, shall have no greater

duration than the warranty period set forth above.  There are no warranties which extend beyond the description in this Limited Warranty.
Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you.

10. DISCLAIMER.  No other express warranty has been made or will be made on behalf of ParaBody with respect to any ParaBody product or

the operation, repair or replacement of any ParaBody product.  ParaBody shall not be responsible for injury, loss of use of the ParaBody
product, inconvenience, loss or damage to personal property, whether direct or indirect, and incidental or consequential damages, so the
above limitation or exclusion may not apply to you.

Summary of Contents for 440 GYM SYSTEM


































Reviews: