ParaBody 897104 Assembly Instructions Manual Download

Page: 10 / 10

STEP 13:

FIGURE 13

!IMPORTANT!

SECURELY

TIGHTEN

JAM NUT

• Screw the threaded end of the CABLE (7) approximately 3/4” into the end of the 20 HOLE SELECTOR SHAFT (5) and tighten jam

nut securely. See FIGURE 13.

Thank you for purchasing the Parabody 897104 WEIGHT STACK OPTION. If unsure of proper use of equip-
ment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.

• If the HEAD PLATE (24) does not sit on top of the first WEIGHT PLATE (25), push the head plate down, insert the SELECTOR PIN

(10) and perform several repetitions on the machine. This will relax the cable system and prevent the HEAD PLATE (24) from lifting up.

• If after completing the previous step the HEAD PLATE (24) still does not sit on top of the first WEIGHT PLATE (25) or if there is

excess slack in the cable system, adjust the threaded end of the CABLE accordingly and retighten the jam nut.

• Insert the WEIGHT STACK PIN (10) into the WEIGHT STACK as shown in FIGURE 13.

1/2

Summary of Contents for 897104











Search results

Summary of Contents for 897104

Reviews:

Related manuals for 897104

Brands by name

Popular brands

ParaBody 897104, Assembly Instructions Manual

Search results

Summary of Contents for 897104

Reviews:

Related manuals for 897104

Brands by name

Popular brands