Esprit 728 Ultra & 738 Ultra
15
5.4
Computer Telephone Number
Streamline Section 02 and 03
D
Hex Programming - Address 008 to 015
The control panel will dial this telephone number when trying to initiate communication with the PC (see
below).
There is no default telephone number and you can enter any number from 0 to 9 up to a maximum of 16 digits. If you would like
to enter any special keys or functions, refer to Table 5 on page 18. If the telephone number contains less than 16 digits, press the
[
TBL
]/[
TRBL
]
key to indicate the end of the telephone number.
[
ENTER
]
+ Installer code +
[7]
+
[0] [2]
+ Telephone Number (if less than 16 digits press
[
TBL
]/[
TRBL
]
) +
[
ENTER
]
5.5
Call Espload
Key Access Programming
D
key
[
TBL
]/[
TRBL
]
The control panel will dial the telephone number entered at addresses 008 to 015 (see
above) in
order to communicate with the Espload software. The control panel and the computer will verify that the Panel Identifier and the
PC Password match before establishing communication (see
on page 14). Espload must be
set in “Wait For Call” mode.
Press
[
ENTER
]
+ (Installer, Master or User code 1) +
[
TBL
]/[
TRBL
]
5.6
Answer Espload
Key Access Programming
D
Key
[
AWAY
]/[
FORCE
]
By entering the code sequence listed below, you can manually force the control panel to answer any incoming calls from the
Espload software. This option can also be used to perform an on-site upload/download by connecting your computer directly to
the control panel using an ADP-1 line adapter and manually answering Espload from the control panel. In Espload go to:
Main Menu
D
Program Setup
D
Modem and Printer Configuration
Set "Dialing Condition" to "Blind Dial". Program the panel telephone number in Espload and follow the instructions on the ADP-1
adapter. When the computer has dialed, press:
[
ENTER
]
+ (Installer, Master or User code 1) +
[
AWAY
]
/
[
FORCE
]
5.7
Cancel Communication
Key Access Programming
D
Key
[
STAY
]
Use the Installer code to cancel all communication and erase any unreported events in the buffer until the next reportable event.
Use the Master or User code 1 to cancel communication attempts with Espload.
[
ENTER
]
+ (Installer, Master and User code 1) +
[
STAY
]
5.8
Call Back
Feature Select Programming
D
Address 086; Key
[4]
Default: Call Back Disabled
For additional security, when a PC using the Espload software attempts to communicate with the control panel, the control panel
can hang-up and call the PC back in order to re-verify identification codes and re-establish communication. When the control
panel answers the call, it will verify if the Panel ID and PC Passwords match and if they do, the control panel will hang-up and call
the Espload software back. The Espload software will automatically go into "wait for dial tone", ready to answer when the control
panel calls back. Please note the Computer Telephone Number (see
in order to use the Call Back feature.
Key
[4]
OFF: Call Back Disabled
Key
[4]
ON: Call Back Enabled
[
ENTER
]
+ Installer code +
[0] [8] [6]
+
[4]
ON/OFF +
[
ENTER
]
twice
5.9
Automatic Event Buffer Transmission
Feature Select Programming
D
Address 088; Key
[2
ND
]
Default: Automatic Event Buffer Transmission Disabled
When the event buffer reaches 50% capacity, the control panel will make two attempts to establish communication with a PC.
The control panel will call the Computer Telephone Number (see
above) programmed at
addresses 008 to 015. The Espload software must be in "wait for dial tone" mode. When the system establishes communication,
it will upload the contents of the event buffer to the Espload software. If communication is interrupted before transmission of the
complete contents of the buffer, or if after two attempts, communication is not established, the system will wait until the event
buffer is full before attempting to re-communicate with Espload. When the Event Buffer is full, each subsequent new event will
erase the oldest event in the buffer.
Key
[2
ND
]
OFF: Automatic Event Buffer Transmission Disabled
Key
[2
ND
]
ON: Automatic Event Buffer Transmission Enabled
[
ENTER
]
+ Installer code +
[0] [8] [8]
+
[2
ND
]
ON/OFF +
[
ENTER
]
twice
Summary of Contents for ESPRIT 728 ULT
Page 1: ...Versions 4 4 728ULT 4 1 738ULT Reference Installation Manual 728ULT 738ULT ...
Page 2: ......
Page 54: ...Notes ...
Page 55: ......
