background image

 12

If the Model 5030 Telephone Line Filter causes harm to the telephone network, the
telephone company will notify you in advance that temporary discontinuance of service
may be required. But if advance notice is not practical, the telephone company will
notify the customer as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens, the
telephone company will provide advance notice in order for you to make necessary
modifications to maintain uninterrupted service.

If trouble is experienced with the Telephone Line Filter, for repair or warranty
information, please refer to 

Warranty, Sales, and Service Information

.

No repairs may be performed by the end user.

The equipment can not be used on public coin phone service provided by the
telephone company. Connection to party line service is subject to state tariffs. Contact
the state public utility commission, public service commission or corporation
commission for information.

Warranty, Sales, and Service Information

Contact your sales or service representative directly for any help needed. For additional
information concerning warranty, sales, service, repair, installation, documentation, or
training, use one of the following methods:

H

Via the Internet:  Visit the Paradyne World Wide Web site at:
http://www.paradyne.com

H

Via Telephone:  Call our automated call system to receive current information via
fax or to speak with a company representative:

—   Within the U.S.A., call 1-800-870-2221
—   International, call 813-530-2340

 

*5030–A2–GN10–10*

Summary of Contents for 5030













Reviews: