background image

6. Maintenance Procedures

6-4

 

 August 2005

8900-A2-GB20-50

Downloading and Switching Firmware

Use the System - Firmware screen to upgrade firmware or switch versions of 
firmware in the chassis.

The SCP card has two banks of firmware: the running firmware and alternate 
firmware. When firmware is downloaded, it is downloaded to the alternate 
firmware bank. Switching firmware versions changes the running firmware to the 
dormant (alternate) firmware, and the alternate firmware to the active (running) 
firmware. 

Downloading Firmware

Procedure

To download new firmware from an FTP server to the SCP card:

1. Enter or select the appropriate parameters in the Firmware Download box as 

shown in the following table.

2. Click on Download. The firmware is downloaded. A Firmware Download 

Status frame is displayed showing the filename, server address, number of 
bytes transferred, and the Transfer Status.

When the download is complete, Transfer Status changes to "Transfer 
completed successfully."

Firmware Download Parameters

FTP Server IP Address

Specify the network address of the FTP server where 
the firmware is to be downloaded from. For example: 

137.90.128.10

User Name

Specify a user name accepted by the FTP server. For 
example: 

admin

Password

Specify a password accepted by the FTP server. For 
example: 

admnpass

Filename

Specify the name or pathname of the firmware file. For 
example: 

/scp_030145.fpi                             

Summary of Contents for 8955



















































Reviews: