background image

 8

Power-On

Refer to the installation instructions that came with your housing to power on the
equipment.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for
any help needed. For additional information concerning warranty, sales, service, repair,
installation, documentation, training, distributor locations, or Paradyne worldwide office
locations, use one of the following methods:

H

Internet:  Visit the Paradyne World Wide Web site at www.paradyne.com
(Be sure to register your warranty at www.paradyne.com/warranty.)

H

Telephone:  Call our automated system to receive current information by fax or to
speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them
to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773,
or send e-mail to userdoc@paradyne.com. Include the number and title of this
document in your correspondence. Please include your name and phone number if you
are willing to provide additional clarification.

Trademarks

FrameSaver and NextEDGE are a registered trademarks of Paradyne Corporation. All
other products and services mentioned herein are the trademarks, service marks,
registered trademarks, or registered service marks of their respective owners.

 

*9109–A2–GN10–50*

Copyright 

E

 2000 Paradyne Corporation. Printed in U.S.A.

Summary of Contents for 9109









Reviews: