background image

18

T1 Facility Interface Codes

If equipped with an ISDN PRI DBM, make the ISDN PRI connection using a USOC-type 
RJ48C jack. When ordering an ISDN line from the telephone company, specify the 
following:

„

Service Order Code 6.0F

„

Facility Interface Code 04DU-1SN

„

Up to 23B Service for an ISDN PRI DBM – Supports up to 23 circuit-switched 
B-channels, with one local phone number for the entire T1 network connection.

„

Circuit Switched Data capability should be specified.

If equipped with an ISDN BRI DBM, make the ISDN BRI connection using a USOC-type 
RJ49C jack. When ordering an ISDN line from the telephone company, specify the 
following:

„

Facility Interface Code 02IS5

„

Calling Number Identification Service (CNIS) for both the originating and answering 
units for data traffic on the B-channel.

„

Capability Package B for 1B-service, which supports up to two circuit-switched 
B-channels, BRI-B1 and BRI-B2, with one Service Profile Identification (SPID) 
number and one local phone number.

Capability Package R for 2B-service, which supports up to two circuit-switched 
B-channels, BRI-B1 and BRI-B2, with two SPID numbers and two local phone 
numbers.

„

Busy Fixed Call Forwarding for the answering system (typically the central site 
system) is recommended if getting Capability Package R (2B-service). This feature 
is only required if all remote systems will call the same phone number. Busy Fixed 
Call Forwarding forwards a call to the BRI-B2 channel when the BRI-B1 channel is 
busy.

Make the modem connection using a USOC-type RJ11C jack. The modem cannot be 
used on public coin phone service provided by the telephone company. Connection to 
party-line service is subject to state tariffs. Contact the state public utility commission, 
public service commission, or corporation commission for tariff information.

Interface Code

Description

04DU9-BN

1.544 Mbps superframe format (SF) without line power

04DU9-DN

1.544 Mbps SF and B8ZS without line power

04DU9-1KN

1.544 Mbps ANSI ESF without line power

04DU-1SN

1.544 Mbps ANSI ESF and B8ZS without line power

Summary of Contents for 9161 Single T1





















Reviews: