background image

19

After the telephone company has installed the requested services and jacks, you can 
connect the DSU with the cable provided. An FCC-compliant telephone cord and 
modular plug are provided with this equipment. This equipment is designed to be 
connected to the telephone network or premises wiring using a compatible modular jack 
that is Part 68 compliant.

Canada
Notice to Users of the Canadian Telephone Network

The Industry Canada label identifies certified equipment. This certification means that 
the equipment meets telecommunications network protective, operational and safety 
requirements as prescribed in the appropriate Terminal Equipment Technical 
Requirements document(s). The Department does not guarantee the equipment will 
operate to the user's satisfaction. 

Before installing this equipment, users should ensure that it is permissible to be 
connected to the facilities of the local telecommunications company. The equipment 
must also be installed using an acceptable method of connection. The customer should 
be aware that compliance with the above conditions may not prevent degradation of 
service in some situations. 

Repairs to certified equipment should be coordinated by a representative designated by 
the supplier. Any repairs or alterations made by the user to this equipment, or equipment 
malfunctions, may give the telecommunications company cause to request to 
disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of 
the power utility, telephone lines and internal metallic water pipe system, if present, are 
connected together. This precaution may be particularly important in rural areas.

CAUTION:

Users should not attempt to make such connections themselves, but should 
contact the appropriate electric inspection authority, or electrician, as 
appropriate.

The Ringer Equivalence Number (REN) assigned to each terminal device provides an 
indication of the maximum number of terminals allowed to be connected to a telephone 
interface. The termination on an interface may consist of any combination of devices 
subject only to the requirement that the sum of the Ringer Equivalence Numbers of all 
the devices does not exceed 5.

If your equipment is in need of repair, refer to 

Warranty, Sales, Service, and Training 

Information

 on page 20.

Summary of Contents for 9161 Single T1





















Reviews: