background image

20

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for 
any help needed. For additional information concerning warranty, sales, service, repair, 
installation, documentation, training, distributor locations, or Paradyne worldwide office 
locations, use one of the following methods:

„

Internet:  Visit the Paradyne World Wide Web site at www.paradyne.com
(Be sure to register your warranty at www.paradyne.com/warranty.)

„

Telephone:  Call our automated system to receive current information by fax or to 
speak with a company representative.

Within the U.S.A., call 1-800-870-2221

Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them to 
Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or 
send e-mail to userdoc@paradyne.com. Include the number and title of this document 
in your correspondence. Please include your name and phone number if you are willing 
to provide additional clarification.

Trademarks

All products and services mentioned herein are the trademarks, service marks, 
registered trademarks, or registered service marks of their respective owners.

"

*9000-A2-GN1D-90*

Copyright © 2001 Paradyne Corporation. Printed in U.S.A.

Summary of Contents for 9161 Single T1





















Reviews: