background image

 1

9261 Dual T1 Network Access Module (NAM)
Installation Instructions

Document Number 9261-A2-GN10-30

October 2000

Product Documentation on the World Wide Web

We provide complete product documentation online. This lets you search the
documentation for specific topics and print only what you need, reducing the waste of
surplus printing. It also helps us maintain competitive prices for our products.

Complete documentation for this product is available at www.paradyne.com.
Select Library 

Technical Manuals 

NextEDGE Multiservices Access System

Documents.

Select the following document:

9161-A2-GH30
Model 916x/926x T1 Access Mux Technical Reference

To order a paper copy of a Paradyne document:

H

Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)

H

Outside the U.S.A., call 1-727-530-8623

Before You Begin

Make sure you have:

-

An operable T1 network connection

-

An asynchronous (VT100-compatible) terminal emulator

-

Housing and other associated hardware

-

Applicable cables

See the Technical Reference for additional information on:

H

Setting Up

H

Troubleshooting and Maintenance

H

Technical Specifications

H

Cables, Connectors, and Pin Assignments

Summary of Contents for 9261













Reviews: