background image

 16

Notices

!

WARNING:

THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE
LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE
FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE
PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT
IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT
GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND,
IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION
MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL
AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE
USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN
EXPENSE. THE AUTHORITY TO OPERATE THIS EQUIPMENT IS
CONDITIONED BY THE REQUIREMENTS THAT NO MODIFICATIONS WILL BE
MADE TO THE EQUIPMENT UNLESS THE CHANGES OR MODIFICATIONS
ARE EXPRESSLY APPROVED BY PARADYNE.

!

WARNING:

           

                 

              

           

           

          

               

              

      

Government Requirements and Equipment Return

Certain governments require that instructions pertaining to modem connection to the
public switched telephone network be included in the installation and operation manual.
Specific instructions are listed in the following sections.

Notice to Users of the United States Public Switched Telephone Network

1. This equipment complies with Part 68 of the FCC rules. On the equipment is a label

that contains, among other information, the FCC registration number and ringer
equivalence number (REN) for this equipment. The label is located on the bottom
of the Model 3830 modem.

2. For the Model 3830 standalone modem, the Universal Service Order Code (USOC)

for Permissive mode is RJ11C. The Canadian equivalent to the USOC is CA11.

Summary of Contents for COMSPHERE 3830





















Reviews: