Paradyne COMSPHERE 6800 Series Command Reference Manual Download | Manualshive

Page: 47 / 237

background image

COMSPHERE 6800 Series Network Management System

2-24

January 1997

6800-A2-GB31-20

Call Fault Read (cfr)

Use the cfr command to display the statistics for the DATAPHONE II DDD modem or
COMSPHERE 3800 Series modem no answer (NA) (displays as non-answering on screen) and
short holding time (HT) faults. These statistics give an overall indication of individual DDD
modem activity. The call fault criteria used to initiate no answer and short holding time faults are
also displayed with this command. The criteria for this command is defined with the Call Fault
Criteria (cfc) command. See the cfc command for more information.

For most commands, NMS enables you to specify the destination for the command’s results and
schedule its execution. If the last page of the input form cannot accommodate the Destination for
results and Schedule execution fields, an additional page is provided. For a complete description
of these fields, refer to Chapter 1, Introduction.

Access Level:

Help Desk, Data Technician, Manager, System Administrator

Abbreviation:

cfr

Restrictions:

None

Routine:

Yes

Schedule:

Yes

Related Commands: Call Fault Criteria (cfc)

Call Fault Read Input Form

This input form contains the following field:

Device(s) (Required field)

Enter the device(s) for which the call fault information will be displayed. One or more
devices may be specified. Standard addressing format applies to input. For information on
device addressing, refer to Appendix D of the COMSPHERE 6800 Series Network
Management System User’s/System Administrator’s Guide.

Call Fault Read Results Form

There are two pages for the Call Fault Read results forms.

«
...
45
46
47
48
49
...
»

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

Brand: Campbell Pages: 3

Sierra Wireless AirLink RV50

Brand: Campbell Pages: 2

Brand: TP-Link Pages: 1

Brand: H3C Pages: 54

Brand: Aztech Pages: 16

Brand: SEA Pages: 2

Brand: AirLive Pages: 77

Brand: Infiniteq Pages: 11

Brand: InfinitiKloud Pages: 2

Brand: MyRepublic Pages: 7

Brand: Zte Pages: 25

Brand: AVM Pages: 51

Brand: FiberHome Pages: 78

HPT104BT Series

Brand: Javad Pages: 44

Brand: Javad Pages: 54

Brand: Javad Pages: 164

Brand: FAAC Pages: 20

Brand: NETGEAR Pages: 208

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands