background image

24

12.

Follow these instructions when rack mounting the equipment.

Maintain an environment compatible with the maximum rated operating 
temperatures indicated in the 

FrameSaver SLV Technical Description. The 

ambient temperature of equipment in a closed or multi-unit rack assembly may 
be higher than the room temperature. 

Install the equipment in a rack such a way that the amount of air flow required 
for safe operation of the equipment is not compromised.

Mount the equipment in a rack in such a way that a hazardous condition is not 
created due to uneven mechanical loading.

Apply the equipment nameplate ratings to ensure that connection of the 
equipment does not overload the supply circuits.

Maintain reliable earthing of rack-mounted equipment, particularly if using 
indirect connections to the branch circuit such as power strips.

13.

This product contains a coin cell lithium battery that is only to be replaced at the 
factory. 

Caution:

 There is a danger of explosion if the battery is incorrectly 

replaced. Replace only with the same type. Dispose of used batteries according to 
the battery manufacturer’s instructions. 

Attention:

 Il y a danger d’explosion s’il y a 

remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du 
même type. Mettre au rebut les batteries usagées conformément aux instructions 
du fabricant.

EMI Notices

UNITED STATES – EMI NOTICE:

!

This equipment has been tested and found to comply with the limits for a 
Class A digital device, pursuant to Part 15 of the FCC rules. These limits are 
designed to provide reasonable protection against harmful interference when 
the equipment is operated in a commercial environment. This equipment 
generates, uses, and can radiate radio frequency energy and, if not installed 
and used in accordance with the instruction manual, may cause harmful 
interference to radio communications. Operation of this equipment in a 
residential area is likely to cause harmful interference, in which case, the user 
will be required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the requirements 
that no modifications will be made to the equipment unless the changes or 
modifications are expressly approved by Paradyne.

CANADA – EMI NOTICE:

!

This Class A digital apparatus meets all requirements of the Canadian 
interference-causing equipment regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du 
règlement sur le matériel brouilleur du Canada.

Summary of Contents for FrameServer SLV 9520-ILM





























Reviews: