background image

27

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for 
any help needed. For additional information concerning warranty, sales, service, repair, 
installation, documentation, training, distributor locations, or Paradyne worldwide office 
locations, use one of the following methods:

Internet:  

Visit the Paradyne World Wide Web site at 

www.paradyne.com

(Be sure to register your warranty at 

www.paradyne.com/warranty

.)

Telephone:  

Call our automated system to receive current information by fax or to 

speak with a company representative.

Within the U.S.A., call 1-800-870-2221

Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them to 
Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or 
send e-mail to 

userdoc@paradyne.com

. Include the number and title of this document 

in your correspondence. Please include your name and phone number if you are willing 
to provide additional clarification.

Trademarks

FrameSaver is a registered trademark of Paradyne Corporation. All other products and 
services mentioned are the trademarks, service marks, registered trademarks, or 
registered service marks of their respective owners.

Patent Notification

FrameSaver products are protected by U.S. Patents: 5,550,700 and 5,654,966. Other 
U.S. patents pending.

Copyright 

©

 2002 Paradyne Corporation. Printed in U.S.A.

Summary of Contents for FrameServer SLV 9520-ILM





























Reviews: