background image

 2

Hotwire 6301/6302 IDSL Routers Overview

The Hotwire

r

 6301 and 6302 ISDL (Integrated Services Digital Network Digital

Subscriber Line) Routers are components in the Hotwire DSLAM (Digital Subscriber
Line Access Multiplexer) system. Both Hotwire IDSL Routers interoperate with either
the Hotwire 8303 or 8304 IP IDSL Line Card:

H

Hotwire 6301 IDSL Router with one Ethernet port

H

Hotwire 6302 IDSL Router with a 4-port Ethernet hub

Both the Hotwire 6301 and the Hotwire 6302 IDSL Routers operate as an IP router
connecting a DSL link to an Ethernet network. The Hotwire IDSL packet-based system
provides high-speed Internet or corporate LAN access over a combination of traditional
twisted-pair copper telephone wiring and ISDN transport, such as T1 or fiber. These
products have three data channels that are configurable for a total of 144 kbps.

Network Overview with a Hotwire 6301 IDSL Router

00-16766

Punchdown

Block or NID

DSL

Jack

6301
IDSL

Router

Customer Premises (CP)

DSL

Ethernet

Crossover

Cable

Ethernet

Cable

or

Central

Office

(CO)

Demarcation

Point

Local

Loop

Hub

End-user

Systems

DSL – Digital Subscriber Line

New Wiring Connections

NID – Network Interface Device

Service

Provider

Remote

Terminal

(RT)

Digital

Loop

Carrier

(DLC)

NOTES:

In this document:

— End-user system is used to represent any host with an Ethernet connection.

— Service provider is used to represent any Internet Service Provider (ISP) or

remote LAN provider.

Summary of Contents for Hotwire 6301





















Reviews: