background image

 

15 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

TROUBLESHOOTING

 

PROBLEM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

 

Main burner will 

not light 

Gas valve may be off 

Turn gas valve ON 

Fuel tank may be empty 

Refill LPG tank 

Orifice blocked 

Clean or replace orifice 

Air in supply system 

Purge air from lines. Open gas 
lines and depress control knob 

for 2-3 mins. 

Loose connection 

Check all fittings 

Igniter fails 

Use stick lighter to manually 

light 

Gas pressure low with valve 

open full 

Replace cylinder or regulator 

New cylinder or 1st ignition 

Purge air from lines 

Cylinder valve on, no gas 

flow 

Replace hose/regulator 

assembly 

AAA Battery behind igniter 

button is dead 

Replace with a new AAA Battery 

Low burner flame 

Pressure is low 

Replace LPG tank 

Tank is low on fuel 

Fill LPG tank 

Gas hose is kinked 

Check & straighten or replace 

Control knob at max 

Check for obstruction at 

passageways and orifices 

Burner unit 

Carbon on reflector & 

emitter screen 

Clean components as needed 

Thick black smoke 

Blockage in burner 

assembly--thoroughly clean 

burner 

 

Summary of Contents for LIP-09A-TGG

















Reviews: