background image

-3 - 

NOTE: PLEASE READ THE FOLLOWING SAFETY RULES

WARNING: 

This heater must only be used outdoors. Using this product in an enclosed area may   
cause injury, death or property damage. 

Only use in a well-ventilated space. Do not use in a building, garage, or any other 
enclosed area. 

Read the instructions before use. This heater must be installed in accordance   
with local codes or, in the absences of local codes, with the National Fuel Code, ANSI 
Z223.1. If applicable, the heater, when installed, must be electrically grounded in 
accordance  with local codes or, in the  absence of local  codes,  with  The National 
Electrical Code, ANSI/NFPA70. 

Do not use the heater in an explosive atmosphere. Keep the heater away from areas 
where gasoline or other flammable liquids or vapors are stored. 

Prior to use, check for damaged parts such as hoses, regulators, pilot or burner. 

Turn off and disconnect LPG cylinder before moving the heater. 

Do  not  attempt  to  alter  this  heater  in  any  manner.  EXAMPLE:  Using  the  heater 
without the top canopy reflector or radiant screen. 

Do not use this heater in basements or below ground level. It must always be placed 
on a solid and level surface. 

Always ensure there is ample fresh air ventilation. For outdoor use ONLY. 

Never replace or substitute the regulator with any regulator other than the factory 
suggested replacement. 

Do not clean the heater with cleaners that are combustible or corrosive. 

Do not paint radiant screen, control panel, or top canopy reflector. 

All leak tests should be done with a soapy solution. NEVER USE AN OPEN FLAME TO 
CHECK FOR LEAKS. 

The LPG cylinder should be turned off when the heater is not in use. 

At least once a year, the unit should be inspected for the presence of spiders, spider 
webs or other insects.   

PRECAUTIONS 

Summary of Contents for LIP-09A-TGG

















Reviews: