background image

TO PUMP

TRUNK LINE MUST BE

SIZED TO MEET MAXIMUM

VELOCITY REQUIREMENTS

FOR SUCTION PLUMBING

PER LOCAL CODE.

65mm OR 90mm

ENLARGED SUCTION ELEMENT

WITH CANISTER AND MV FUSE

IF NOT USING HYDROSTAT

PLUG 2" PORT

MV FUSE IN

CANISTER

IF NOT USING HYDROSTAT

PLUG 2" PORT

65mm OR 90mm

WITH CANISTER WITHOUT MV FUSE

ENLARGED SUCTION ELEMENT

TRUNK LINE MUST BE

SIZED TO MEET MAXIMUM

VELOCITY REQUIREMENTS

FOR SUCTION PLUMBING

PER LOCAL CODE.

TO PUMP

WITH CANISTER

WITH CANISTER

WITHOUT CANISTER

WITHOUT CANISTER

TO PUMP

TRUNK LINE MUST BE

SIZED TO MEET MAXIMUM

VELOCITY REQUIREMENTS

FOR SUCTION PLUMBING

PER LOCAL CODE.

65mm OR 90mm

ENLARGED SUCTION ELEMENT

WITH DECK FUSE

IF NOT USING HYDROSTAT

PLUG 2" PORT

MV FUSE DECK SIDE

TO PUMP

TRUNK LINE MUST BE

SIZED TO MEET MAXIMUM

VELOCITY REQUIREMENTS

FOR SUCTION PLUMBING

PER LOCAL CODE.

65mm OR 90mm

WITHOUT CANISTER, WITHOUT MV FUSE

ENLARGED SUCTION ELEMENT

IF NOT USING HYDROSTAT

PLUG 2" PORT

*Note: Canister requires 40mm equalizer line through pool wall. (Not Shown)

*Note: Canister requires 40mm equalizer line through pool wall. (Not Shown)

ENLARGED SUCTION ELEMENT

IF NOT USING HYDROSTAT

PLUG 2" PORT

SDX

2ND SUCTION OUTLET

2 1/2"

2 1/2"

TO PUMP

TRUNK LINE MUST BE

SIZED TO MEET MAXIMUM

VELOCITY REQUIREMENTS

FOR SUCTION PLUMBING

PER LOCAL CODE.

WITH CANISTER AND MV FUSE

MV FUSE IN

CANISTER

IF NOT USING HYDROSTAT

PLUG 2" PORT

ENLARGED SUCTION ELEMENT

2 1/2"

2 1/2"

TRUNK LINE MUST BE

SIZED TO MEET MAXINUM

VELOCITY REQUIREMENTS

FOR SUCTION PLUMBING

PER LOCAL CODE.

TO PUMP

SDX

2ND SUCTION OUTLET

WITH DECK SIDE MV FUSE

MV FUSE DECK SIDE

SDX

2ND SUCTION OUTLET

2 1/2"

2 1/2"

ENLARGED SUCTION ELEMENT

IF NOT USING HYDROSTAT

PLUG 2" PORT

TRUNK LINE MUST BE

SIZED TO MEET MAXIMUM

VELOCITY REQUIREMENTS

FOR SUCTION PLUMBING

PER LOCAL CODE.

TO PUMP

WITH CANISTER, WITHOUT MV FUSE

TO PUMP

TRUNK LINE MUST BE

SIZED TO MEET MAXIMUM

VELOCITY REQUIREMENTS

FOR SUCTION PLUMBING

PER LOCAL CODE.

SDX

2ND SUCTION OUTLET

2 1/2"

ENLARGED SUCTION ELEMENT

WITHOUT CANISTER, WITHOUT MV FUSE

IF NOT USING HYDROSTAT

PLUG 2" PORT

2 1/2"

*Note: Canister requires 1½” equalizer line through pool wall. (Not Shown)

MDX-R3 INSTALLATION WITHOUT SKIMMER INSTALLED

MDX-R3 INSTALLATION WITHOUT SKIMMER INSTALLED

Summary of Contents for MDX-R3













Reviews: