background image

INTRODUCTION

4

Thank You for Choosing Parasound

Congratulations on your purchase of this precision component and thank you for your selection 
of Parasound. Please take a few moments to review this manual so you may enjoy all the  
benefits of your new Ztuner v.2’s unique features and capabilities.

Unpacking

Carefully unpack your Ztuner v.2 and these accessories:

  Detachable AC power cord

  Remote handset

  2 AAA batteries

  Black trigger wire with a 2.5 mm sub-mini plug at each end 

  Black trigger wire with a 2.5mm plug on one end and a 3.5mm plug on the other 

  FM antenna, flexible dual wire “folded dipole” 

  FM antenna 300 

Ω

 to 75 

Ω

 “balun” transformer/connector 

  AM loop antenna 

  2 page RS-232 programming guide

Please inspect the unit now and contact your Parasound Dealer promptly if you see evidence  
of shipping damage. Save the carton and packing inserts in case you move or in the event you 
need to ship your amplifier for repair. Before you proceed, locate the serial number on the rear 
panel or underside of the unit and record it here for future reference:

OWNERSHIP REFERENCE INFORMATION

  Parasound Serial Number:

  

  Date of Purchase:

                   /      /

  Name of Dealer:

               

  Dealer Street Address:

        

  Dealer Phone:

                  (      )      -

Summary of Contents for Ztuner v.2

















Reviews: