background image

                                                            

 

21 

 

BATTERY HANDLING 

Rescue Guardian Rechargeable Li-ion Battery with Protection Circuit 

The Rescue Guardian uses lithium-ion protected circuit 18650 batteries. 
Fully charged Rescue Guardian batteries will typically last one week, depending on settings. 
Keep batteries away from fire or other sources of heat above 80° C. 
Storage Temperature: -10° C to 40° C 
 

Hot Swapping 

Batteries may be replaced one by one while the Rescue Guardian is operating. To do this, remove the 
Rescue Guardian Battery Lid and begin to replace each battery one at a time with a fully charged 
replacement. Once complete, make sure to correctly re-install the Rescue Guardian Battery Lid. 

 

ALTERNATE POWER 

CR123A Lithium Batteries - Adapter Tubes  

The Rescue Guardian will operate using four (4) CR123A lithium batteries as an alternative 
emergency power source. Paratech has available adapter tubes. Each tube holds two (2) 
CR123A batteries (fig 2). 
 

CAUTION

: when putting the CR123A lithium batteries in the adapter tubes, make sure that the 

batteries are correctly orientated and observe correct polarity. Make sure that polarity 
markings on the adapter tube, batteries and Rescue Guardian Battery compartment markings 
are aligned. 
 

WARNING:

 DO NOT USE CR123 lithium-ion batteries. Please note that the higher voltage of the 

lithium-ion cells could damage Rescue Guardian circuitry. Make sure to check the battery type 
before using the adaptor tubes. Understand the difference between lithium and lithium-ion 
batteries. Physical cell size is the same, but the chemistry is very different. 

BEWARE

: Use of lithium-ion batteries will void warranty. 

 

 

Figure 2: Four CR123A lithium 
batteries inserted into two 
adapter tubes.

 

Summary of Contents for 22-796RG1






























Reviews: