background image

5

BATTERY AND CHARGER

11.1V (3 cell) 1300mAh (C)  LiPo Battery rated at
15C max discharge.

12v DC input  0.8 A output  balancing type fast
charger for 2 and 3 cell packs.

12v crocodile clip connecting lead

ADHESIVE

5ml tube of foam safe adhesive.

Note pierce end of tube with pin in screw on lid.

SECTION 2: BATTERY AND CHARGER

BATTERY AND CHARGER

The kit includes a high performance 11.1V (3 cell)

1300mAh LiPo Battery rated at 15C (19.5 amp) max
discharge.
This must be charged using the dedicated 12v DC
input  0.8 Amp output  fast charger and connecting
lead

Connect the crocodile lead connectors to a 12V DC
power source (a 12V car battery is ideal), ensuring
that correct polarity is observed. Red is positive (+)
and Black is Negative (-).

Connect the lead into the matching socket of the
battery charger and the Red LED will illuminate.

WARNING:

A lithium polymer (LiPo) battery rated at 15C
(19.5A) discharge and fast charger is included as
part of this package, these cells must be
operated with care to prevent the risk of fire.

LiPo Batteries are soft cased and can be easily
damaged by sharp items, puncturing of the soft
casing can cause fires and we recommend that
they are stored and handled carefully.

Use only the supplied balance charger or a LiPo
rated charger set to a maximum of 3 cells (11.1v)
and less than 1 amp charge current.

Remove battery from the aircraft and charge on a

non flammable, non conductive surface 

Summary of Contents for Mirage 2000













Reviews: